Acoustic Research AWSBTSK - Manual

Powering the Speaker
There are two options to power your wireless speaker: using the included AC power
adapter or using 6 AA batteries (not included).
AC Power Adapter
1. Insert the small, round plug from the speaker
AC power adapter into the DC IN jack on the
side panel of the speaker.
2. Plug the other end of the speaker AC power
adapter into any standard 120V AC wall
outlet.
Note: The power unit should be plugged in so
that it stays vertical or lies fl at.
AA Batteries
1. Twist the bolts on the bottom of the speaker counter-clockwise to loosen them
completely.
2. Remove the bottom of the speaker to access the battery compartment.
3. Insert six (6) AA batteries (not included) into the battery compartment, following the
polarity diagrams (+ and –).
4. Line the bolts on the compartment door up with the holes on either side of the battery
compartment and place the speaker bottom back on the speaker.
5. Screw the bolts back in and tighten them.
Note: Place the rubber cap in the speaker power input jack when using batteries.
DO NOT mix batteries with different chemistry types (for example, a zinc battery with an
alkaline battery). DO NOT mix new and used batteries. DO NOT leave batteries installed in
the product when not in use for long periods. Always remove old, weak or worn-out batteries
promptly and recycle or dispose of them in accordance with local and national regulations.
Introduction
The Acoustic Research AWSBTSK customizable portable wireless speaker makes it easy to
take your music wherever you go and share it whenever you want, with Bluetooth® wireless
connectivity and a built-in auxiliary input. It’s compact, easy-to-carry and simple to use, and
a free customizable speaker skin from SkinIt lets you make this speaker truly your own, with
thousands of designs to choose from, including professional and college sports teams, popular
entertainment and social icons, even your own photo or design.
This manual covers various connection options and detailed operating instructions for making
the Acoustic Research customizable portable wireless speaker a part of your lifestyle. If, after
having reviewed the instructions, you have any questions, please call toll-free 1-800-732-6866
or visit www.acoustic-research.com
Important Information
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION
Caution: To reduce the risk of electric shock, do not remove cover (or back).
No user serviceable parts inside. Refer servicing to qualifi ed service personnel.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record
the serial and model numbers in case you need them. These num bers are located on the product.
Model No.: __________________________________________________________________________________________
Purchase Date: ______________________________________________________________________________________
Dealer/Address/Phone: _______________________________________________________________________________
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers)
that produce heat.
8. Protect the power cord from being walked on or pinched particularly at plugs, con ve nience re cep ta cles, and the point
where they exit from the apparatus.
9. Unplug this apparatus during lightning storms or when unused for long periods of time.
10. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been dam aged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the ap pa ra tus has been exposed to rain or moisture, does not op er ate normally, or has been dropped.
Care and Maintenance
• Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol or other
solvents as they may damage the surface.
• Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.
• If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a rainstorm to
prevent possible damage.
• Do not operate or store the system in extreme temperatures (below 32ºF/0ºC and above 122ºF/50ºC).
Tour of the Speaker
Front
Back
Power and Pairing indicator shows the status
of the speaker.
Blue, slow blinking: The speaker is on but not
paired or connected (like when you turn the
speaker on for the first time).
Blue, fast blinking: The speaker is in Bluetooth
pairing mode. See the Bluetooth Setup section for
more information.
Solid blue: The speaker is paired with a Bluetooth-
enabled device and ready to play audio.
Solid green: The auxiliary audio input is selected.
See the Using the Auxiliary Input section for more
information.
Top
turns the speaker on and off (press and hold for
3 seconds). It also toggles between Bluetooth and
auxiliary input for the audio signal (press).
Pair puts the speaker in pairing mode for
Bluetooth setup (press and hold for 3 seconds). It
also performs a fast reconnect with devices that
have lost connection (press). See the Bluetooth
setup section for more information.
Volume +/– buttons adjust the speaker’s volume
level
Carrying
handle
Powering the Speaker System
Speaker
(side panel)
120V AC
wall outlet
AC Power
Adapter
Model AWSBTSK
User Guide
Portable
Wireless
Speaker
Battery Compartment Cover
Side
DC IN receives the small round end of the
included 9V 1100mA AC power adapter; remove
the protective cover to insert the adapter.
Bottom
Battery Compartment cover is held in place by two metal bolts
that help keep the speaker sealed against the elements. See the
Powering the Speaker: AA Batteries section for instructions on
removing this cover and inserting batteries.
Storage compartment houses the built-in cable
for the speaker’s auxiliary input. It also offers a closed
compartment for your connected device or other items. See
the Using the Auxiliary Input section for more information.
Setting Up Bluetooth Wireless
Pairing
Any Bluetooth-enabled device that you wish to stream audio to your speaker system must
fi rst be paired to the speaker. The process is simple, and in most cases the pairing process
needs to be done only once.
To pair your Bluetooth-enabled device with the speaker:
1. Make sure your device’s Bluetooth is turned on. See the wireless and/or network
settings menu on your device to check.
2. If the speaker isn’t already on, press and hold the button for 3 seconds to turn it on.
You will hear 4 beeps to indicate the speaker is turned on. The indicator light on the
front of the speaker starts fl ashing blue.
3. Press and hold for 3 seconds the Pair button to enter pairing mode. You will hear 2
beeps to indicate pairing mode is entered. The indicator on the front of the speaker
starts blinking faster.
4. Open the Bluetooth settings menu on your device. Select “AWSBT1” from the list
of devices available (you might have to scan for devices). If your device asks for a
password, enter “0000”.
5. A confi rmation screen will appear on your device once the speaker and the device
are successfully paired. The blue indicator turns solid blue to indicate successful
connection. The speaker is now ready for you to stream audio from your device.
6. Turn the volume on your device to at least 3/4 max, then start playing something on
the device. Control the speaker volume on the speaker itself, using the +/– buttons on
the top of the speaker.
Note:
• If you notice the sound from the speaker is distorted, turn down your device’s volume.
• You will hear a beep if you turn the speaker’s volume up to the maximum.