Remington PG6030 - Manual (Page 3)

4 5
ENGLISH ENGLISH
any waxes or lotions before using the groomer
,To thin and taper beards or moustache
• Attach the wide trimmer blade.
• Place the hair length attachment on the trimmer blade, select the desired length and
switch on.
• Start trimming under the chin, following the jawbone line. Work toward the ear and
upper beard line using an upward motion.
,To trim edge of beard or moustache
• Attach the detail trimmer blade.
• Hold groomer with cutting blade facing you.
• Start with edge of beard/moustache line, and with the cutting blades resting lightly
against your skin, use slow movements to create a beard/moustache line.
,To trim sideburns
• Hold groomer with cutting blade facing you.
• Use a small comb to lift the hairs. Hold the comb at the desired beard or moustache
length.
• Move the groomer along the comb to cut the hairs. Use light pressure and well-controlled
movements to trim hair.
,Trimming the nape of your neck
• Attach the wide trimmer blade.
• Use your fingers to lift the hair at the base of your head up off the neck. Your index finger
should be covering the roots of the hairs you are lifting to prevent accidental removal by
groomer.
• Using your other hand, hold the groomer to the base of your neck with the cutting unit
facing up, and move the groomer up the length of the neck until the unit touches your
finger covering the hair roots at the base of your head.
Move the unit slowly when performing this operation and to keep the hair roots at the
base of your head out of the way of the groomer.
,To remove hair from nose and ear
• Attach nose, ear & eyebrow attachment.
• Insert groomer’s cutting unit gently into the nostril or ear.
• Gently move the groomer in and out of the nostril or ear and at the same time rotate the
groomer.
• Avoid inserting the cutting unit more than 6mm into your nostril or ear.
,To remove hair from eyebrows
• Attach nose, ear, eyebrow attachment.
• Gently guide cutting unit to stray, unwanted hairs along the eyebrow line or protruding
from the eyebrow itself.
• To remove the hairs completely lower onto the skin and move over desired area.
• Use slow and well-controlled movements.
E Tips for best results
Comb your hair in the direction that it grows so that the hairs are at their maximum height and
facing in the same direction.
After trimming, lightly go over the trimmed areas with the foil to get a smooth clean finish.
Since all hairs do not grow in the same direction, you may want to try different trimming
positions (i.e. upwards, downwards or across) for better results.
,Attaching and removing the trimmer attachments.
Note: Always ensure the groomer is switched off before changing any attachments.
• To remove, hold the groomer with one hand and turn the trimmer head anti-clockwise
with the other.
• To attach, hold the groomer with on hand and turn the trimmer head clockwise with the
other.
,Using the detailed trimmer
• Hold groomer with the surface (back side) of the blade guides against the skin.
• Use motions similar to using a wet blade to provide the closest trim.
Note: This attachment provides a dual purpose solution for stubble or close results
without irritation.
,Using your miniscreen shaver
• Hold the groomer so the MiniScreen gently touches your face.
• Use short, and well-controlled movements to shave around your beard/moustache. Use
your free hand to stretch your skin. This encourages the hair to stand upright, making it
easier to shave.
Note: The MiniScreen shaver was designed to shave the detail areas around your beard
moustache/sideburns. It was not designed to shave your entire face. For a close
comfortable shave, guaranteed, use one of Remington’s electric shavers.
C CARE FOR YOUR GROOMER
Care for your product to ensure a long lasting performance. We recommend that you clean your
groomer after each use.
The easiest and the most hygienic way to clean the groomer is by rinsing the product head after
use with warm water. Always keep the protective cap on the shaving head and keep the trimmer
in the “off” position when the shaver is not in use.
E After each use
• Rinse the accumulated hair from the cutters and shake off excess water. Alternatively, use
a brush.
• Gently tap on a flat surface to remove hair particles, and brush the remaining hairs away.
• Place one or two drops of cutter oil or sewing machine oil on the blades. Turn the clipper
on to distribute the oil evenly, wipe off any excess oil.
• Wipe the main unit with a damp cloth and dry immediately.
Note: Ensure that the groomer is turned off when applying
the oil or rinsing under the tap.