Candy FO FS 817 AQUA - Manual (Page 10)

The first operation to carry out after the oven
has been installed or following the interruption
of power supply (this is recognizable the display
pulsating and showing 12:00) is setting the
correct time.
• Turn the selector knob (1)
to the symbol.
• Using the and buttons,
set the time of day (while
setting, the numbers on
the display will flash)
• When knob (1) is turned
to the symbol, the light
comes on
USE OF THE PROGRAMMER
FUNCTION HOW TO ACTIVATE ITHOW TO SWITCH IT OFF WHAT IT DOES WAT IT IS FOR
• This function is useful for
checking that the oven is
fully operational.
• Using the and buttons,
set the time of day (while
setting, the numbers on the
display will flash)
NB: Set the clock imme-
diately after installing the
appliance or after an inter-
ruption to the power sup-
ply (this is shown by 12:00
flashing on the display).
• Turn the selector knob to
the position
• Allows you to regulate the
time shown on the oven
clock
OVEN
LIGH
CLOCK
THE PROGRAMMER
Clock display Safety display
Control buttons Programmer function
display
A slight delay will occour when setting a programme, while the
oven carries out internal diagnostics.
9 GB
• This function is used typi-
cally used with ‘cooking
time’ function. For example
if the dish has to be
cooked for 45 minutes and
needs to be ready by
12:30, simply select the
required function, set the
cooking time to 45 minutes
and the end of cooking
time to 12:30.
Cooking will start automa-
tically at 11:45 (12:30
minus 45 mins) and
will continue until the pre-
set end-of-cooking-time,
when the oven will switch
itself off automatically.
• Select a cooking func-
tion (selector knob 2)
• Turn the selector knob to
the symbol.
• Set the end of cooking time
using the and buttons
(while setting, the numbers
on the display will flash)
• At the pre-set time the oven
automatically switches
itself off. If you need to stop
it before then, switch the
oven off by turning the
selector knob 2 to the
symbol.
• Allows the end of cooking
time to be stored in the
memory.
• When the cooking time has
been set, turn selector
knob 1 to the symbol to
display the time of day.
• To display the programmed
time turn selector knob 1
to the symbol.
END OF
COOKING
ALARM • Provides an audible alarm
signal (for a few seconds)
at the end of cooking time.
• Useful as a reminder
• This function works
independently of the
oven (it can be used
even when the oven is
not working)
• To select a cooking fun-
ction use (selector knob 2)
• Turn selector knob 1 to the
symbol
• Set the cooking time using
the and buttons (while
setting, the numbers on
the display will flash)
• When the cooking time is
up, the oven will switch it
self off.
If you need to stop it before
then, the oven must be
switched off, or the cooking
time must be turned to 00:00.
(selector 1 to symbol ,
and use the and
buttons)
• Allows the end of cooking
time to be stored in the
memory.
• When the cooking time
has been set, turn selector
knob 1 to the symbol
to display the time of day.
• To display the programmed
time turn selector knob 1
to the symbol.
• When the set cooking time
is up the oven switches
itself off automatically and
for a few seconds an alarm
sounds.
COOKING
TIME
CHILD
SAFETY • Press buttons and
together for three seconds.
The light flashes.
• The oven settings cannot
be altered (even when the
knobs are accidentally
adjusted)
• Operates even when the
oven is not on preventing
it from being inadvertently
switched on.
• Is operational when the
oven is on and prevents
any alterations to the
settings (through acciden-
tal turning of the knobs)
NB: the oven can still be
switched off by turning se-
lector knob 2 to position 0.
• Turn selector knob 1 to the
symbol.
• Set the cooking time using
the and buttons (while
setting, the numbers on
the display will flash)
• When the set cooking time
is up, the oven will auto-
matically switch itself off. If
you need to stop it before
then, you must turn the set
time to 0 (selector knob 1
on and then use the
and buttons)
• Turn the selector knob 1
to the symbol. The
indicator light will flash.
• Press the and buttons
at the same time, for three
seconds.
• The setting is confirmed
when the light stops
flashing.
WARNING: