Candy CDI 1012 - S - Manual (Page 12)

23
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme end
At the end of the programme, the indicator
light for the
“recommended” programme
or the indicator light for the programme that
was used at least 3 times consecutively will
start to blink.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for new cycle.
Option button
"HALF LOAD" button
By using this option, it is possible to wash
a smaller quantity of crockery: you should
load only the upper basket for dishes and
place cutlery in the tray in the bottom
basket.
This reduces water and energy consumption
and requires a smaller quantity of
detergent.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the "COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button. After
checking to make sure the water inlet hose
tap is open, that the drain hose is not bent
and that the siphon or filters are not
clogged, set the selected programme
again. If the anomaly persists, contact
Customer Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
22
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
IMPORTANT
The dishwasher has two very practical
functions:
- the "recommended" programme
(which is ideal for full load daily use)
for quick and accurate selection;
- the "Auto’ Memory", function saves
any programme used at least 3 times
consecutively, so that if you regularly
use the same washing cycle you
do not have to continually set the
programme thereby saving time and
effort.
Programme settings
■ Open the door and place the dirty dishes
inside the appliance.
■ Press the "ON/OFF" button .
■ After pressing the "ON/OFF" button,
the indicator light which is factory set at
"recommended” , or the indicator light
for the "Auto’ Memory" programme will
flash.
■ If you wish to select an option, press the
option button (the corresponding indicator
light will light up).
The option button can be selected or
deselected WITHIN 2 minutes of the
programme commencing.
■ Choose a programme by pressing the
corresponding button.
■ To start the programme, close the door.
IMPORTANT
To select the "COLD RINSE" programme,
simultaneously press the "RAPID"
programme button and "HALF LOAD"
option button.
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically.
Close the door,
without pressing any
buttons . The cycle will start from where it
left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running program:
■ Open the door.
■ Hold down the current programme button
(with the indicator light on) for at least 5
seconds. The programme indicator lights
(except for the "RAPID" programme
indicator light) will flash.
■ The running programme will be cancelled
and the indicator light for the
“recommended” programme or the
indicator light for the programme that
was used at least 3 times consecutively
will start to flash.
■ At this point a new programme can be set.
IMPORTANT
To
cancel the "COLD RINSE"
programme, simultaneously hold
down the "RAPID" programme button
and "HALF LOAD" option button.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.