English – Milwaukee HD 18 AG User Manual

Page 18

................... 18 V

............... 9000 (min

-1

)

..................115 mm

............... M 14

.................. 2,4 kg

................ 74,5 dB(A)

................ 85,5 dB(A)

.................. 6,1 m/s

.................. 1,5 m/s

ENGLISH

TECHNICAL DATA

Cordless Angle Grinder

Battery voltage..............................................................................

Max. no-load speed ......................................................................

Grinding disk diameter..................................................................

Thread of work spindle ................................................................

Weight according EPTA-Procedure 01/2003 ................................
Noise/Vibration Information

Measured values determined according to EN 60745.Typically,

the A-weighted noise levels of the

tool are:

Sound pressure level (K = 3 dB(A)) ............................................

Sound power level (K = 3 dB(A)) ................................................

Wear ear protection!
Total vibration values (vector sum in the three axes) determined

according to EN 60745:

Surface grinding: vibration emission value a

..............................

Uncertainty K = ............................................................................

For other applications, e.g. Abrasive Cutting-Off Operations or

Wire Brushing other vibration values could occur.

WARNING! Read all safety warnings and all

instructions, including those given in the accompanying

brochure. Failure to follow the warnings and instructions may

result in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

General safety instructions for grinding, working with wire

brushes and abrasive cutting.
a) This power tool is intended to function as a grinder, wire

brush, or cut-off tool. Read all safety warnings,

instructions, illustrations and specifi cations provided with

this power tool. Failure to follow all instructions listed below

may result in electric shock, fi re and/or serious injury.
b) Operations such as sanding or polishing are not

recommended to be performed with this power tool.

Operations for which the power tool was not designed may

create a hazard and cause personal injury.
c) Do not use accessories which are not specifi cally

designed and recommended by the tool manufacturer. Just

because the accessory can be attached to your power tool, it

does not assure safe operation.
d) The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fl y apart.
e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.
f) The arbour size of wheels, fl anges, backing pads or any

other accessory must properly fi t the spindle of the power

tool. Accessories with arbour holes that do not match the

mounting hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from the

plane of the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and shop apron capable of stopping

small abrasive or workpiece fragments. The eye protection

must be capable of stopping fl ying debris generated by various

operations. The dust mask or respirator must be capable of

fi ltrating particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a broken

accessory may fl y away and cause injury beyond immediate

area of operation.
j) Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a „live“ wire may make exposed metal

parts of the power tool „live“ and could give the operator an

electric shock.
k) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.
l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.
m) Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical hazards.
n) Do not operate the power tool near fl ammable materials.

Sparks could ignite these materials.
o) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in electrocution

or shock.

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different

applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase the

exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is

running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work patterns.

289 037 - HD18AG.indd 18

07.11.2012 14:04:05