Makita 5143R - Manual (Page 6)

6
ENGLISH
Explanation of general view
1 To avoid kickback, do support
board or panel near the cut.
2 Don’t support board or panel
away from the cut.
3 A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing.
4 Hex wrench
5 Shaft lock
6 Tighten
7 Loosen
8 Saw blade
9 Outer flange
10 Inner flange
11 Hex socket head bolt
12 Saw blade
13 Setting protuberances
14 Hex socket head bolt
(For adjusting riving knife)
15 Cutting depth
16 Loosen
17 Lever
18 Thumb nut
19 For 45
°
bevel cuts
20 For straight cuts
21 Base plate
22 45
°
angle cuts
23 Straight cuts
24 Top guide
25 Base
26 60° angle cuts
27 30° angle cuts
28 Blade
29 Lock-off button
30 Switch trigger
31 Vacuum cleaner
32 Limit mark
33 Brush holder cap
34 Screwdriver
SPECIFICATIONS
Model 5603R 5703R 5903R 5103R 5143R
Blade diameter........................................... 165 mm 190 mm 235 mm 270mm 355 mm
Max. cutting depth
At 90
°
..................................................... 54 mm 66 mm 85 mm 100 mm 130 mm
At 45
°
..................................................... 38 mm 46 mm 64 mm 73 mm 90 mm
No load speed (min
–1
) .............................. 5,000 4,800 4,500 3,800 2,700
Overall length ............................................ 330 mm 356 mm 400 mm 442 mm 607 mm
Net weight ................................................. 4.2 kg 5.2 kg 7.6 kg 9.4 kg 14.5 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
For model 5703R, public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.36 Ohms it
can be presumed that there will be no negative
effects. The mains socket used for this device must
be protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
SAFETY INSTRUCTIONS
Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don’t expose power tools to rain. Don’t use
power tools in damp or wet locations. Keep work
area well lit. Don’t use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
6. Don’t force tool
It will do the job better and safer at the rate for
which it was intended.
7. Use right tool
Don’t force small tools or attachments to do the
job of a heavy duty tool. Don’t use tools for pur-
poses not intended; for example, don’t use circu-
lar saw for cutting tree limbs or logs.