Yamaha RX-395RDS - Manual (Page 7)

7
English
1
POWER switch
Press this switch to switch the power on. Press it again to
switch the power off.
* Standby mode
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit to the standby
mode. (In this mode, the power indicator is half illuminated.)
2
Power indicator
Lights up while the power is on.
3
Remote control sensor
Receives signals from the remote control transmitter.
4
RDS MODE/FREQ button
RX-495RDS and RX-395RDS only
When an RDS station is received, pressing this button changes
the display mode into the PS mode, PTY mode, RT mode and/or
CT mode (if the station employs those RDS data services), and
frequency display in turn.
5
Display panel
Shows station frequencies and various information. (Refer to
the next page for details.)
6
FM/AM buttons
Press this button to switch the reception band to FM or AM.
7
TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
8
EDIT button
This button is used to exchange the places of two preset
stations with each other.
9
MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the MEMO(RY) indicator flashes
for about 5 seconds. During this period, press the desired
PRESET STATIONS button to enter the displayed station into
the memory.
When this button is pressed and holded for about 3 seconds,
the automatic preset tuning begins.
0
Input selector buttons
Select a program source to listen to. When a button is
pressed, the name of selected source lights up on the display.
A
PURE DIRECT switch
RX-495RDS only
Press this switch to listen to a source in the purest sound.
(Refer to page 16 for details.)
B
PHONES jack
When you listen with headphones,
connect the headphones to the
PHONES jack. When listening with
headphones privately, set both the
SPEAKERS A and B switches to the
OFF position.
C
SPEAKERS switches
Set the switch A or B (or both A and B) for the speaker system
(connected to this unit) you will use to the ON position. Set the
switch for the speaker system you will not use to the OFF
position.
D
PTY SEEK MODE button
RX-495RDS and RX-395RDS only
When this button is pressed, the unit turns into the PTY SEEK
mode.
E
PTY SEEK START button
RX-495RDS and RX-395RDS only
Press this button to begin searching for a station after the desired
program type is selected in the PTY SEEK mode.
F
EON button
RX-495RDS and RX-395RDS only
Press this button to select a desired program type (NEWS,
INFO, AFFAIRS, SPORT) when you want to call a radio
program of that program type automatically.
G
TUNING MODE (AUTO/MAN’L) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that “AUTO (TUNING)” lights up on the display. To
select the manual tuning mode, press this button so that “AUTO
(TUNING)” goes off.
H
Tone controls
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
I
BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
J
A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
K
PRESET STATIONS buttons
Used to enter as many as 40 station frequencies into the
memory.
L
Continuously variable LOUDNESS control
Used to compensate for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
M
VOLUME control
Used to raise or lower the volume level.
PHONES