Yamaha HTR-5440RDS - Manual (Page 30)

28
TUNING
Automatic Preset Tuning (for RDS
stations only)
You can make use of the automatic preset tuning function
for RDS stations only. This function enables the unit to
automatically tune in with strong signals and to sequentially
store up to 40 RDS stations (5 groups x 8 stations).
1 Press FM/AM to select the FM band.
2 Press TUNING MODE (AUTO/MAN’L MONO) so
that the “AUTO” indicator lights up on the
display.
3 Hold down MEMORY (MAN’L/AUTO FM) for
about 3 seconds.
The preset number, the “MEMORY” and “AUTO”
indicators flash. After about 5 seconds, automatic
preset tuning begins from the frequency currently
displayed toward the higher frequencies.
Received stations are sequentially stored as A1, A2 ...
A8. If more than 8 stations have been tuned, they are
stored as preset station numbers in other groups (B, C,
D and E) in that order.
■ Automatic preset tuning options
You can select the preset number from which the unit will
store RDS stations and/or begin tuning toward lower
frequencies. Before automatic preset tuning begins (after
pressing MEMORY in step 3),
1. Press A/B/C/D/E and PRESET/TUNING l or h to
select the preset number with which the first station will
be stored. The automatic preset tuning will stop when
stations have all been stored up to E8.
2. Press PRESET/TUNING (EDIT) to turn “ z ” off and
then press PRESET/TUNING l to begin tuning toward
lower frequencies.
■ When automatic preset tuning is
completed
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure in the section “To Recall a Preset
Station” on page 29.
Notes
• A new setting can be stored in place of the former one.
• The reception mode is stored along with the station frequency.
• You can manually replace a preset station with another FM or AM
station by simply using the manual preset tuning method.
• Automatic preset tuning will be performed for all RDS network
stations until all have been stored up to E8. Even if the number of
received stations is not enough to be stored up to E8, automatic
preset tuning is automatically ended after searching for all
stations.
• Only RDS stations with sufficient signal strength are stored by
automatic preset tuning. If the station you want to store is weak in
signal strength, tune in to it manually in monaural mode and store
it by using the manual preset tuning method. (There may be a
case that this unit cannot receive a station which could be
received by using the automatic tuning method. This is because
this unit receives a large amount of PI (Program Identification)
data along with the station.)
Memory back-up
The memory back-up circuit prevents the stored data
from being lost when this unit is set in the standby mode.
If, however, the power cord is disconnected from the AC
power outlet or the power is cut for more than one week,
the memory will be erased. If so, store the stations again
by using preset tuning methods.
Lights up
SILENT
PHONES VIDEO L AUDIO R
6CH INPUT INPUT MODE
INPUT
VOLUME
RDS MODE/FREQ EON
PTY SEEK MODE START
TUNING MODE
PRESET /TUNING FM/AM
MEMORY
EDIT
BASS BALANCE SPEAKERS
PROGRAM PRESET/TUNING EFFECT A/B/C/D/E A B
OFF ON
STANDBY /ON
D I G I T A L
– + L R
TREBLE
– +
MAN'L/AUTO FM AUTO/MAN'L MONO
SURROUND
D I G I T A L
VIDEO AUX
21 3
FM/AM
TUNING
MODE
AUTO/MAN'L MONO
MEMORY
MAN'L/AUTO FM
MEMORY BASS EXT.
AUTO
Flashes
0105V420RDS26-30_EN 2/12/1, 1:35 PM 28