Yale CB512X - Manual

CB512X USER GUIDE
1. Connect the shredder with power source in accordance with
the power specifications indicated on the bottom label of the
head. Turn the switch to the “On/Auto” position, the shredder
is at the standby mode.
2. Place the paper, credit card of CD in the relevant insertion slot,
the shredder will automatically start to work and restore to the
standby mode when the process is complete.
3. In a normal shredding process, if you suddenly change your
mind and want to keep the remainder paper, you can turn the
switch to the position “REV”, the shredder will roll your paper
out immediately (You would not get any information from the
CD or Credit Card as long as they had been destroyed).
4. If excessive paper has been fed at once, the shredding speed
might be very slow or even stop, in this case, you should turn
the switch to the state of “REV” at once and reduce the
amount of paper to resume the shredding process.
5. For continuous paper shredding in large quantity, it is
recommended not to feed over seven pieces of paper each
time and minimize the consecutive using time to 2 minutes.
Thank you for purchasing the cross-cut paper shredder of the CB512X Series. This product is ideal for office use with its
advanced function and design. This paper shredder will satisfy all your requirements for confidential and safe documnet
disposal.
OPERATING INSTRUCTIONS
Hence, you can properly protect your shredder for
higherefficiency.
6. If the shredder is jammed for a long time or high internal
temperature after continuous paper shredding in a large
amount, the shredder will be shut down as a result of preset
temperature protection. Turn the power off for a while, the
shredder will then automatically resume to the standby mode.
7. Place the paper being shredded is comparatively wet or with
long fiber contents, group blades might be wrapped up with
too much paper, which will affect the efficiency of shreddin. In
this case, made the shredder running clockwise or
counterclockwise in turn for two or three times by sliding the
switch between the state of “On/Auto” and “REV” for two or
three times, wastepaper then can be cleaned automatically off
those group blades.
8. Since certain safety protection has been preset intentionally,
the shredder can not startup normally if the head is moved
away from paper backet or the head is not placed at proper
specified level over the basket.
1. Please locate the shredder at places nearby power socket for
quick power disconnection in emergency.
2. Please be aware of the safety alert label on the cover of
shredder, be sure to ensure human body safety by prevention
tie, jewellery or hair from being placed into the machine.
3. Please never place non-paper goods such as clip, plastic bag
or cloth into the shredder to avoid shredder damage and lower
the shredding performance.
4. While cleaning the shredder or cleaning out the paper basket.
Please turn the switch to the state of “Off” and unplug the
power. Please clean out the basket regularly.
ATTENTION AND SAFETY INSTRUCTION
MAIN PERFORMANCE PARAMETERS
5. In order to ensure long using life and good performance of the
shredder, please do not run the shredder in the environment
with heat or wet sources for a long time.
6. Do not renovate the internal structure of the shredder or power
connection cable in any way by yourself. Do not use the
shredder if the body or cable is damaged, contact with your
dealer or dial the service hotline.
7. Please keep the shredder away from children and pets.
Shredder Type: Cross-cut & CD break
Cut size (mm): 4*25 / Shred CD into 3 pcs
Capacity: 7 sheets (70g) / 1pc CD
Speed: 3m/min (7 sheets)
Throat width (mm): 228
Size (mm): 330X240X395
Paper Basket Capacity (Liter): 20
CD Basket Capacity (Piece):
20
Net weight (kg): 5.5
The Meadows, Cannock Road, Wolverhampton WV10 0RR, England
Tel: +44 (0) 1902 364 647 Fax: +44 (0) 1902 867 158 www.yale.co.uk