Ariston Aqualtis AQ8F 29 U H - Manual (Page 7)

EN
7
Wash options
Super Wash
This option offers a high-performance wash due to the
greater quantity of water used in the initial phase of the
cycle, and due to the increased wash cycle duration, is
particularly useful for the
removal of stubborn stains.
It can be used with or
without bleach. If you desire
bleaching, insert the extra
tray compartment (3) into
compartment 1. When
pouring in the bleach, be
careful not to exceed the
“max” level marked on the
central pivot (see figure).
To bleach laundry without
carrying out a full wash cycle, pour the bleach into the
extra compartment 3, select the "Rinse" cycle and
activate the "Super Wash" option .
It cannot be used in conjunction with , , , , ,
, , .
Easy Iron
By selecting this option, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine
drum will rotate slowly; the “Easy Iron” and START/
PAUSE indicator lights will flash. To end the cycle press
the START/PAUSE button or the “Easy Iron” button.
For the Silk wash cycle, the machine will end the
cycle while the laundry is soaking and the “Easy
Iron” indicator light will flash. To drain the water so that
the laundry may be removed, press the START/PAUSE
button or the “Easy Iron” button.
It cannot be used in conjunction with , , , , .
Time Saver
If you select this option, the wash cycle duration will be
reduced by 30%-50%, depending on the selected cycle,
thereby guaranteeing simultaneous water and energy
saving. Use this cycle for lightly soiled garments.
It cannot be used in conjunction with , , , ,
, , , , .
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal residual detergent removal is
guaranteed. It is particularly useful for skin which is
sensitive to detergents. We recommend this option is
used with a full load of washing, or when a large amount
of detergent is required.
It cannot be used in conjunction with , , .
3
1
2
(*)
The
duration
of
the
wash
cycles
can
be
checked
on
the
display
.
Wash cycles and options
Table of wash cycles
Icon Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergent and additives
Max.
load
(kg)
Cycle
duration
Detergent
for wash
Fabric
softener
Bleach
Cottons wash cycles
Cottons with pre-wash
(Add detergent to the relevant compartment).
90° 1200 l l - 8
Cottons (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200 l l l 8
Cottons (1-2): heavily soiled whites and delicate colours. 40° 1200 l l l 8
Coloured Cottons (3) 40° 1200 l l l 8
Shirts 40° 600 l l l 2
Jeans 40° 800 l l - 4
Special programmes
Baby: heavily soiled delicate colours
40° 800 l l l 4
Durable Synthetics 60° 800 l l l 4
Delicate Synthetics 40° 800 l l l 4
"Bed & Bath" for bedlinen and towels. 60° 1200 l l l 8
Duvets: for down-stuffed garments. 30° 1000 l l - 3,5
Silk: for garments in silk and viscose, lingerie. 30° 0 l l - 2
Wool: for wool, cashmere, etc. 40° 600 l l - 2
Mix 30': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand)
30° 800 l l - 3,5
Partials wash cycles
Rinse
- 1200 - l l 8
Spin - 1200 - - - 8
Drain - 0 - - - 8
For all Test Institutes:
1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle with a temperature of 60°C and 40°C.
2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle with a temperature of 40°C.
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle with a temperature of 60°C .
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
CH RU TR
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.