Whirlpool WHCF-DUF User Manual
Model whcf-duf, Under sink main faucet filtration, Installation, use & care guide
Model
WHCF-DUF
Filter Replacement:
The contaminants or other substances removed or reduced by
this water filter are not necessarily in all users’ water.
Filter life varies depending on local water conditions and the vol-
ume of water used. We recommend that you change your filter
every 6 months. However, it can be replaced earlier if there is a
drop in pressure at the faucet.
To reduce Chlorine Taste and Odor,
use Replacement Filter: WHCF-GAC
Do not use with water that is microbiologically unsafe or of unknown quali-
ty without adequate disinfection before or after the system.
Systems certified for Cyst reduction may be used on disinfected water
that may contain filterable cysts. EPA Establishment #070595-CT-001
Filter Cartridge Replacement Instructions:
NOTE: Before changing cartridge, turn off incoming water
supply. Place a bucket under filter to catch the small amount
of water that will run out after housing removal.
1. Shut off water.
2. Relieve pressure in housing by pushing red vent button.
3. Unscrew housing and remove old cartridge. Wash housing
thoroughly with mild soap and water.
4. Insert new cartridge and re-install housing. Be sure cartridge is
seated in the housing before tightening onto head.
5. Use filter wrench to fully seat the cartridge. Tighten to make a
water tight seal.
6. Turn on water. If any leaks appear, tighten housing as needed.
7. Flush system for five (5) minutes.
Troubleshooting Guide
Water Leaks at Threaded Fittings:
Tighten slightly more until leak stops.
Water leaks at Push-in Connections
Push tubing in as far as it will go. If leaking continues, shut off
water at the original valve and remove water line by pushing in on
the connector collar while pulling the tubing away. (See Push-in
Fittings Section) Inspect tubing for cracks and scratches. If tubing
is cracked or scratched, simply cut that portion away and reinsert
tubing into fitting.
Make sure tubing is cut straight. If not, recut.
Help Line 1-866-245-9474
Monday Through Friday
8:00 a.m. to 9:00 p.m. EST
or write us at
Whirlpool Water Products
PO Box 765
Meriden, CT 06450
INSTR7016 1203
04/04
8562175
Whirlpool Water Products
Meriden, CT 06450
UNDER SINK MAIN FAUCET
FILTRATION
Standard System
Installation, Use & Care Guide
8562175/INSTR7016 1203
® Registered trademark/TM Trademark of Whirlpool, USA,
used under license.
© 2004 Whirlpool Corporation. All rights reserved.
TEFLON is a registered trademark of E.I. Dupont
® Marca registrada/TM Marca de comercio de Whirlpool, USA,
usado bajo licencia.
Todos los derechos reservados.
TEFLON es una marca registrada de E.I. Dupont
1 Year Limited Warranty
CUNO Incorporated warrants the original purchaser-consumer of its Product
that is free of defects in materials and workmanship. Any defect, malfunction, or
other failure of the Product to conform to this warranty will be remedied by
Warrantor in the manner provided below.
This Warranty, together with any warranties implied by law, shall be limited to a
duration of one (1) year from the original date of purchase by the consumer.
This Warranty does not apply to defects that result from abuse, misuse, alter-
ation or damage not caused by CUNO Incorporated.
THIS WARRANTY DOES NOT COVER, AND IS INTENDED TO EXCLUDE ANY
LIABILITY ON THE PART OF WARRANTOR, WHETHER UNDER THIS WAR-
RANTY OR UNDER ANY WARRANTY IMPLIED BY LAW, FOR ANY INDIRECT
OR CONSEQUENTIAL DAMAGES FOR BREACH HEREOF OR THEREOF.
Note: Some states prohibit limitations on the duration of implied warranties and
on the exclusion of indirect or consequential damages; and so the limitation on
implied warranties and on incidental and consequential damages may not be
applicable to you.
RESPONSIBILITY OF WARRANTOR
CUNO Incorporated’s responsibility under this warranty shall be to repair at its
expense, at no charge to the original purchaser-consumer any product that is
actually defective, malfunctioning or otherwise in violation of this warranty. If
CUNO Incorporated for any reason cannot repair a Product covered hereby
within two (2) weeks after receipt of the original purchaser-consumer’s notifica-
tion of a Warranty claim and the Product, then CUNO Incorporated’s responsi-
bility shall be, at its option, either to replace the defective Product with a compa-
rable new unit at no charge to the consumer or to refund the full purchase price.
CUNO Incorporated’s obligations of repair, replacement, or refund are condi-
tioned upon the return of the defective product to CUNO Incorporated.
If any Product hereby is actually defective within the terms of this Warranty, then
CUNO Incorporated will bear all the reasonable and proper shipping and mail-
ing charges actually incurred in the consumer’s return of the Product set forth
herein. If the Product proves not to be defective within the terms of this
Warranty, then all costs and expenses in connection with the processing of the
consumer’s claim hereunder shall be borne by the consumer.
RESPONSIBILITY OF THE CONSUMER
The original purchaser-consumer’s sole responsibility in the instance of a war-
ranty claim shall be to notify CUNO Incorporated of the defect, malfunction or
other manner in which the terms of this Warranty are violated. You may secure
performance or obligations hereunder by (in writing):
1. Identifying the Product involved (by model or serial number or other sufficient
description that will allow Warrantor to determine which product is defective).
2. Specifying where, when and from whom the Product was purchased.
3. Describing the nature of the defect, malfunction or other violation of this
Warranty.
4. Return the Product, with the above information to:
CUNO Incorporated, 400 Research Parkway, Meriden, CT 06450, U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
To
Release Tubing
Push in gre
y
collet to release
tubing.With collet
held, pull tubing
straight out.
To
Attach
Tubing
Push tubing in as far as
it will go.T
ubing must be
inserted past o-r
ing and
hit backstop
.Pull tube
to ensure it is secured.
Collet
Backstop
“Using Push-In Fittings”
6.Wr
ap T eflon
®
tape (2 1/2
wraps) around the 3/8”
fit-
ting in a clockwise direction
and fasten to filter head
(see Figure 5).Do not use
pipe sealant (dope), as sol-
vents in some types of pipe
dope may cause damage to
plastic fittings.
7.Inser
t water supply line to
port mar
ked "IN" (see
Figure 6, A) and insert
faucet line to por
t mark
ed
"OUT" (see Figure 6, B).
Referr
ing to section “Using
Push-in Fittings,”
insert
plastic tubing into fittings,
making sure end of tubing
is firmly seated to bac
kstop.
8.F
asten brac
ket to filter head with
four Phillips head scre
ws provided.
(See Figure 7.) Fasten br
acket to w
all
with four Phillips head scre
ws provid-
ed.If pre-dr
illing holes, br
acket ma
y
be used as a template for making
screw hole locations
.
9.Lubr
icate housing o-ring with w
ater.
10.Place filter into housing.
(See Figure 8.)
Align housing to filter head and screw
onto filter head.Tighten with wrench to
seal.
11.Slo
wly turn w
ater supply on while depressing red air
release button on filter head and chec
k for leaks
.Then r
un
water f
or 5 minutes with an open f
aucet to flush out air.
3/8" Compression
Hex Nut
3/8" Ferr
ule
3/8" T ube
Insert
3/8" x 1/2"
Faucet Adapter
Installation Instructions
For Use With Cold
Water Onl
y
NOTE:
Remove
items from under the sink.Place a catch basin
there to collect small amounts of water that ma
y run out when dis-
connecting water supply lines
.
1.T
urn
off cold water supply v
alve and remo
ve
existing fitting and/or
tubing from cold water side of f
aucet.
2.Loosely assemb
le sump to filter head and attach filter brac
ket.
Use this assembly to mar
k a location under the sink that is not in
the wa
y but allo
ws for easy access to change filter
.Allo
w room to
operate housing wrench and a minim
um of 2 1/2”clear space belo
w
the unit to facilitate changing car
tridge
.Once this is done disassem-
ble components f
or installation.
3.Deter
mine length of tubing required from filter
head/brac
ket to f
aucet and from water supply line
to filter head/brac
ket b
y holding tubing in place
ensuring it is of appropr
iate length.Do not kink
tubing as this will impede water flo
w.
If necessary,
loop tubing around to avoid it being kink
ed.
Cut tubing straight with a utility knif
e or tube cut-
ter (for copper piping).
(See Figure 1.)
4.Install f
aucet adapter fitting to faucet (see
Figure 2).Do not o
ver
tighten to prevent dam-
age to fitting.Ref
erring to section
“Using
Push-In Fittings”, insert a section of plastic
tubing into fitting, making sure end of tubing is
firmly seated to bac
kstop.
5.Onto one end of the remaining sec-
tion of tubing, slide the compression
hex n
ut and ferr
ule onto the tubing and
put in the tube insert (see Figure 3).
Fasten this assemb
ly onto 3/8”w
ater
supply outlet.
Do not over
tighten (see
Figure 4).Ov
ertightening will cause
tubing to separate from fitting.
Red Air
Release Button
A
B
Inlet
Outlet
1.
Filter Head
2.
Filter Head Brac
ket
and eight Phillips
head screws
3.
Housing Wrench
4.
Filter Cartr
idge
5.
Opaque Housing
6.
5’of 3/8”
T ubing
7.
3/8”Fitting x 1/2”
Faucet Adapter
8.
3/8”Compression
Hex Nut
9.
3/8”F
errule
10.
3/8”T
ube Insert
11.
T w
o 3/8”x 3/8”
Push-In Fittings
Pa
rts and Material Inc
luded:
Kit contains components necessary to connect 3/8”
outlet tube to 1/2”
faucet fitting and 3/8”
water supply
.If y
ou have
any other siz
e faucet
connection, you ma
y need other parts f
or installation as required.
This filter can be used at any sink where w
ater is used for dr
inking.
Figure 1
Figure 3
Correct
Incorrect
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Gather the required tools before star
ting installation.Read and f
ol-
low the instr
uctions provided with an
y tools listed here.
To
ols and Pa
rts Needed:
•
Phillips Head Screwdr
iver
•
Adjustable Wrench
•
T eflon
®
T ape
•
Utility Knife or
T ube Cutter f
or
copper piping
Installation Requirements:
•
Properly tighten all fittings to ensure a leak-free assemb
ly .
•
Install in a location that is not susceptible to freezing temper
atures
as damage to the housing could occur.
•
Install aw
ay
from direct sunlight as prolonged exposure to light
can weak
en plastic components.
•
Some local codes may require the use of a licensed plumber or
certified installer when disr
upting a potable w
ater line.
Determine
and follo
w any and all local codes and requirements
.
•
Allow room to oper
ate housing wrench and a minimum of 2 1/2”
clear space below the unit to f
acilitate changing of the filter.
Figure 2