Wharfedale RS-10 - Manual (Page 2)

Before making any connections, switch the amplifier off.
When you switch on your system or change sources, set the
volume control at minimum and turn the level up
gradually.
DO NOT use your amplifier at full volume.
Ensure that all loudspeakers in the system are correctly
wired.
DO NOT subject your loudspeakers to excessive cold, heat,
humidity or sunlight.
DO NOT place heavy objects on top of loudspeakers
DO NOT connect loudspeakers to the mains supply.
DO NOT dismantle the loudspeaker. There are no user
serviceable parts inside it and you will void the warranty.
Before installing this product
read all these instructions!
PRELIMINARIES
UNPACKING YOUR LOUDSPEAKERS
After taking out the top-most packing piece, lift the
loudspeakers and accessories from the carton and remove
all the polythene bags.
The contents of each carton are as follows:
RS-10 Satellites:
! Two RS-10 satellite speakers
! Two wall brackets*
RS-10 Centre:
! One RS-10 Centre speaker
! One wall bracket*
! One table stand with mounting hardware
Check all the items after unpacking. If any item is missing or
damaged, immediately contact your Wharfedale dealer.
Retain the packaging. If you decide to dispose of the
packing, follow all recycling regulations in your area.
* Note: No hardware is supplied to attach wall brackets to walls.
Table stands and floor stands for the RS-10 satellites are available
as optional extras from your dealer.
PREPARATIONS FOR INSTALLATION
Positive (+) terminal is on the left and has a Red collar. The STANDS AND BRACKETS
Negative (–) terminal is on the right and has a Black collar.
RS-10 loudspeakers must be operated attached to wall brackets
To connect the terminals: Unscrew each terminal. Thread the or stands. Wall brackets are supplied for all RS-10 models and a
bare end of the cable through the cross-hole in the terminal table stand is also supplied for the RS-10 Centre speaker.
ensuring there are no loose strands. Tighten securely.
Optional table stands and floor stands for RS-10 satellites are
available in pairs from your Wharfedale dealer.
Use only the designed stands or brackets supplied with the units.
CONNECTORS AND CABLES
You will need five lengths of two core cable. The cables
connecting the Front loudspeakers should be the same length
and the cables connecting the Rear loudspeakers should also be
of equal length. We suggest you use cable designed for audio
and not general purpose ‘bell’ or ‘zip’ wire.
Loudspeaker cable is polarity coded along one edge. Split the
cable to a depth of 25mm and strip 8mm of insulation from each
wire. If the cable is stranded, twist the strands together.
RS-10 loudspeakers have two connection terminals. The
Before connecting your system consider where you will place the
speakers in the room. This is particularly important if you are
wall mounting loudspeakers.
b c
subwoofer. When you set the LFE level at your AV processor, use Delay Settings
care as the powerful low frequencies can overload domestic
Many AV processors feature delay settings. The purpose of delay
loudspeakers. If you hear popping or thumping noises coming
is to enable surround and dialogue information to arrive at the
from the front loudspeakers or subwoofer, immediately turn the
listener’s ears at the same time as the Front channels, even when
AV Processor's volume level down and then back off the LFE level.
the listening seat is in a non-ideal position.
This should cure the problem. If it does not, back off the volume
Rear Delay: If the listening position is equidistant from the level at the subwoofer. Please read the relevant sections of your
Front and Rear speakers, a low delay setting should be set. The AV amplifier manual and familiarise yourself with the various
closer the listener is to the Rear speakers the higher should be the issues. If you are unsure, consult your dealer for help.
delay setting used, Phase
A Home Theatre system should have a precise front stage, a
Centre Delay: If the Centre speaker is level with (or slightly
diffuse rear stage and good localisation of dialogue. If the behind) the Front speakers, set the delay to zero. If the Centre
colours on the loudspeaker terminals do not correspond with
speaker is forward of the Front speakers, increase the delay.
those on the amplifier, the sound will appear poorly focused or
LFE
‘out of phase’. For this reason it is essential that the speakers are
In domestic systems the LFE channel typically feeds into the connected according to the wiring diagrams in this manual.
CARE
The cabinets can be occasionally wiped with a damp (not wet)
cloth. Spray polishes can be used but they must not be sprayed
onto the grilles or drive units. Spray a very small amount of
polish onto a cleaning cloth not the loudspeaker.
Wharfedale will not be liable for any consequential damage, loss
or injury, arising from or in conjunction with this equipment.
The warranty on this product if it is sold outside the United
Kingdom shall comply with applicable law and shall be the sole
responsibility of the distributor that supplied this product.
WARRANTY IN THE UK
In the unlikely even that your unit develops a fault you should
return it to your Wharfedale dealer using the original packing to
ensure safe shipping. The terms of your warranty may vary in
different countries but in all cases the guarantee excludes:
All damage caused through accident, misuse, wear and tear,
neglect, incorrect installation, adjustment or repair by
unauthorised personnel. Liability for damage or loss occurring in
transit to or from the purchaser.
CARE AND SERVICE
Service Addresses, UK & USA
IAG Service Centre
Unit 4, St Margaret’s Way
Stukeley Meadows Industrial Estate
Huntingdon, Cambs,
PE29 6EB
England
Tel:+44 (0)1480 452561
Fax: +44 (0)1480 13403 IAG America, Inc.
15 Walpole Park South
Walpole
MA 02081
USA
Tel: +1 508 850 3950
Fax +1 508 850 3905
1 6