Whistler TOTAL BAND PROTECTION XTR-695 - Manual (Page 3)

Important: S ome newer cars have a plastic safety
coating on the inside of the windshield. The
windshield bracket may leave permanent marks on
this type of surface. To find out if your vehicle has
this type of windshield, check the vehicle’s owner’s
manual or ask your dealer. We recommend that you
do not leave the suction cup bracket on the window
in direct sunlight. If the detector is removed, this
may cause blistering of the dash in some
vehicles.
• Slide the detector onto the bracket until it locks into
place.
• If necessary, the unit may be leveled by bending
the windshield bracket. Press the bracket release
button and remove the detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit’s power jack.
• Plug the large end into the vehicle’s cigarette
lighter socket.
N No otte e:: Cord fits tightly into detector. When
installing the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp, 3AG fuse located behind the
silver tip. To replace the fuse, carefully unscrew
the tip of the plug.
IIm
mp po orrtta an ntt:: Unscrew slowly. The tip contains a
spring which may fly out when disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, screw cap on plug may loosen.
Retighten occasionally.
INSTALLATION OPERATION
6 7
Power On, Self Test
To turn the unit ON or OFF, push the center of
the Power/Volume button.
Each time your Whistler detector is turned on,
an automatic self-test sequence confirms that
the speaker and visual displays are functional.
• Display shows in order:
1. WHISTLER 2. X-band 3. K-band 4. Ka-band
5. LASER ON 6.. SR OFF 7. VOICE ON
8. POP ON 9. B SVR ON 10. FILTER 11. COMBO
12. HIGHWAY
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
• Press City and Quiet buttons simultaneously
• Display Shows:
• Press Dark button to exit.
Setting Saver
Setting Saver saves your personalized settings
so that when the detector is turned off and then
on again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed, one beep confirms
feature “on”, two beeps confirm feature “off”.
Integrated Real Voice ®
When selected, Real Voice ® will be used to
articulate the following:
1. Band Identification
2. Safety Warning System messages
3. Feature Selection
Note: In certain cases, the voice message does not
replicate the text message.
Audio Level Adjustment
To change the audio level:
• Move Power/Volume button back to increase
audio level.
• Move Power/Volume button forward to
decrease audio level. As audio level is
adjusted, beeps are provided and the display
indicates volume level.
Auto Quiet Mode
Auto Quiet mode reduces the selected audio level
to level (1) approximately 5 seconds after a radar or
safety radar signal is detected. The alert for any
new signal within 20 seconds will resume at level (1).
Auto Quiet mode does not affect laser alerts.
• Press Quiet (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Quiet Mode
Quiet mode cancels audio during an alert and any
new alert within 20 seconds. After 20 seconds of no
radar signal detected, on the XTR-690, 2 beeps are
provided on any new alert and then the audio
remains quiet; on the XTR-695 the audio alerts are
restored.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to
restore the standard audio alert pattern; or turn
the unit off, then on.
External Audio Jack (XTR-695 only)
The 2.5mm external audio jack can be used to
connect an external speaker or headphones in
environments with high ambient noise levels. The
internal speaker will be disconnected.
OPERATION
8