Williams 2503531 - Manual (Page 12)

12 201843
DIRECT-VENT PROPANE/LP GAS HEATER
THE COMFORT PRODUCTS PEOPLE
WARNING: Furnace burner,
combustion chamber, and ex-
haust port are very hot during
operation. Keep children and
adults away from hot surfaces to
avoid burns and clothing igni-
tion. Carefully supervise young
children when they are in the
same room as furnace. Furnace
will remain hot for a time after
shutdown. Let surface cool be-
fore touching.
OPERATING
FURNACE
WARNING: Do not operate
furnace with front cover removed.
Unsafe operation could result.
CAUTION: Do not block cir-
culating air openings in the lou-
ver of the front cover. This is
necessary for furnace to operate
properly.
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury, or loss of life.
A. This appliance does not have a pilot.
It is equipped with an ignition device
which automatically lights the
burner. Do not try to light the burner
by hand.
NOTICE: If operating furnace for
the first time, a slight odor will
occur. This odor will go away
after a few hours of operation.
OPERATING
INSTRUCTIONS
WARNING: Always follow
lighting instructions. Never at-
tempt to light burner with a match
or butane torch.
1. STOP! Read the safety information,
column 1.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the
furnace.
4. Turn equipment shutoff valve clock-
wise
to OFF position (see
Figure 18).
5. Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation, column 1. If you don’t
smell gas, go to next step.
6. Turn equipment shutoff valve coun-
terclockwise
to ON position
(see Figure 18).
7. This furnace is equipped with an ig-
nition device which automatically
lights the burner. Do not try to light
the burner by hand.
8. Plug in furnace.
9. Set thermostat to desired setting. If
thermostat is set above room tem-
perature, the blower will come on.
10. Allow approximately 45 seconds for
ignition to occur. When ignition oc-
curs, the glo-bar will stay on for a
short period of time. The flame sens-
ing probe will sense the burner flame
and shut off glo-bar.
If ignition does not occur within 22
seconds, the ignition control will at-
tempt to light burner three times. This
will take about two minutes. If igni-
tion does not occur, the ignition con-
trol will lock out the glo-bar and valve
circuit. Air in the gas line or a short
gas interruption will prevent furnace
from igniting. If this happens, turn
thermostat off and wait 5 minutes.
Turn the thermostat back on. The fur-
nace will try to ignite again.
11. If the furnace still does not ignite, fol-
low instructions To Turn Off Gas to
Furnace, page 13. Call a qualified
service person. Do not attempt to re-
start furnace.
B. BEFORE OPERATING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
C. Use only your hand to turn the
handle on the equipment shutoff
valve. Never use tools. If the handle
will not turn by hand, don’t try to
repair it. Call a qualified service tech-
nician. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
Figure 18 - Equipment Shutoff Valve
O
POSI
PO Off Position
On Position