beautypg.com

Template instructions, Drilling from inside the cabinet, Drilling from under the cabinet – Whirlpool 8204864/3828W5U0311 User Manual

Page 4

background image

Template instructions

Drilling from inside the cabinet

If you cannot drill from inside the
cabinet, see "Drilling from under the
cabinet" section.

If the cabinet does not have a partition or
you are not installing under two
adjoining cabinets:

Place template inside the cabinet so
that the front line of the Template A will
be aligned with the front edge of the
cabinet. If necessary, cut some areas of
the template in order to make it fit
properly within cabinet.

See NOTE at bottom of page.

If the cabinet has a partition or you are
installing under two adjoining cabinets:

1. Cut Template B from template A along

the dotted line.

2. Cut Template A into two pieces to fit

each side of the partition.

3. Position one piece of Template A inside

cabinet making sure the front line is
aligned with the front edge of the
cabinet. Tape in place.

4. Position Template B in front of the

cabinet so that the hole centerline is
aligned with the hole centerline of the
Template A piece positioned in Step 3
above.

5. Position the other piece of Template A

inside the adjacent cabinet opening so
that the hole centerline aligns with the
hole centerline on Template B. Tape in
place. If you have followed the
instructions properly, the distance
between the right and left hole
centerlines will be 12-7/8" (32.7 cm).

See NOTE to right.

piece of
Template A

front frame
of cabinet

partition

Template B

other piece of
Template A

Template B

12-7/8"

(32.7 cm)

Drilling from under the cabinet

If the cabinet does not have a front frame
exending below the cabinet, there is no
partition, or you are not installing under
two adjoining cabinets:

Tape Template A to the underside of

cabinet so the front line of template
will be aligned with the front edge of
the cabinet. If necessary, cut some
areas of the template in order to make
it fit properly on the underside of
cabinet.

See NOTE at bottom of page.

If cabinet has only a front frame
extending below the cabinet bottom and
no partition:

Measure the thickness of the frame.
Fold template along guide line that
matches the frame thickness. Place the
folded edge of template against the
back side of front frame on the
underside of the cabinet. Tape in place.

See NOTE at bottom of page.

Part No. 8204864/3828W5U0311

© 2004 Whirlpool Corporation.

Printed in China

2/2004

If the cabinet has a partition, you are
installing under two adjoining cabinets,
or there is a side frame as shown:

1. Cut Template B from template A

along the dotted line.

2. Cut Template A into two pieces to fit

each side of the partition or adjoining
cabinets.

3. Position one piece of Template A

under cabinet making sure the front
line is positioned against the back
side of front frame on the underside
of the cabinet. Tape in place.

4. Position Template B toward the rear

of the cabinet so that the hole
centerline is aligned with the hole
centerline of the Template A piece
positioned in Step 3 above.

5. Position the other piece of Template A

under the adjacent cabinet opening
so that the hole centerline aligns with
the hole centerline on Template B.
Tape in place. If you have followed
the instructions properly, the distance
between the right and left hole
centerlines will be 12-7/8" (32.7 cm).

See NOTE below.

piece of
Template A

partition or
adjoining cabinets

front frame
of cabinet

side frame

Template B

other piece
of Template A

Template B

12-7/8" (32.7 cm)

NOTE: For any of the template instructions used, when Template A is properly
installed, the distance from the front edge of the cabinet with cabinet door(s)
open to the centerlines of the front holes will be 2-1/16" (5.2 cm).

Return to Step 3 of “Installation steps.”

2-1/16"
(5.2 cm)

Template A