Weed Eater 530088127 User Manual

Page 6

-- 6 --

Watch out for children, pets, open windows,

or freshly washed cars. Blow debris away

safely.

Use the full blower nozzle extension so the

air stream can work close to the ground.

After using blowers and other equipment,

CLEAN UP! Dispose of debris in trash re-

ceptacles.

BEFORE STARTING ENGINE

WARNING:

Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723

FUELING ENGINE

WARNING:

Remove fuel cap slowly

when refueling.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

mixed with a good quality synthetic 2-cycle

air-cooled engine oil designed to be mixed at a

ratio of 40:1. Poulan/Weed Eater brand

synthetic oil is recommended. Mix gasoline and

oil at a ratio of 40:1. A 40:1 ratio is obtained by

mixing 3.2 ounces of oil with 1 gallon of

unleaded gasoline. DO NOT USE automotive

oil or boat oil. These oils will cause engine

damage. When mixing fuel, follow instructions

printed on container. Once oil is added to

gasoline, shake container momentarily to

assure that the fuel is thoroughly mixed. Always

read and follow the safety rules relating to fuel

before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads to

separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid

engine problems, empty the fuel system

before storage for 30 days or longer. Drain the

gas tank, start the engine and let it run until the

fuel lines and carburetor are empty. Use fresh

fuel next season.

Never use engine or

carburetor cleaner products in the fuel tank or

permanent damage may occur.

TO STOP THE ENGINE

To stop the engine, move the throttle lever

to the STOP position.

BEFORE STARTING THE ENGINE

WARNING:

You MUST make sure

the tubes are secure before using the unit.

Fuel engine. Move at least 10 feet (3 me-

ters) away from the fueling site.

Hold the unit in the starting position as

shown. Make sure the blower end is di-

rected away from people, animals, glass,

and solid objects.

Blower

Vacuum

STARTING POSITION

WARNING:

When starting engine,

hold the unit as illustrated. Do not set unit on any

surface except a clean, hard area when starting

engine or while engine is running. Debris such

as gravel, sand, dust, grass, etc. could be

picked up by the air intake and thrown out

through the discharge opening, damaging the

unit or property, or causing serious injury to by-

standers or the operator.

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

1. Move throttle lever to the

position.

2. Move choke lever to the FULL CHOKE

position.

3. Slowly press the primer button 8 times.

Throttle Lever

Choke Lever

Primer Button

4. Pull starter rope sharply until engine at-

tempts to run, but no more than 5 pulls (be-

low 30_ F, 8 pulls).

NOTE:

If engine attempts to start before the

pull, go to next step immediately.

5. Move the choke lever to the HALF

CHOKE position.

6. Pull the starter rope sharply until the en-

gine runs, but no more than 5 pulls (below

30_ F, 10 pulls).

7. After a 5 second warm--up, move the

choke lever to the RUN position.

8. Allow the unit to run for 30 more seconds

at the RUN position before moving the

throttle lever to

position.

If engine has not started after 5 pulls (at HALF

CHOKE), repeat STARTING A COLD ENGINE

procedure. If engine still does not start, proceed

to STARTING A FLOODED ENGINE.

9. To stop the engine, move the throttle lever to

the STOP position.