Vestax PMC-CX - Manual (Page 4)

q PHONO / LINE SELECTOR
Selects the signal (PHONO or LINE) to be sent to each
INPUT. All phono inputs are RIAA equalized. Connect
the output of a CD player, MD player, and tape deck to
the line input.
w INPUT ASSIGN SWITCH
Selects the input to be sent to each PGM channel.
e PGM TRIM VOLUME
Adjusts the input level of each PGM channel. PGM
LEVEL METER to indicate at about 0dB.
r PGM BALANCE VOLUME
Adjusts the stereo balance for each PGM channel. Can be used
for adjusting the unbalanced stereo image. Clockwise rotation
from center position increases the volume of R over L channel.
A counter clockwise rotation increases the volume of L
channel over R.
t PGM ISOLATOR HI
Adjusts the HI frequency level of each PGM.
y PGM ISOLATOR MID
Adjusts the MID frequency level of each PGM.
u PGM ISOLATOR LOW
Adjusts the LOW frequency level of each PGM.
i ISOLATOR ON/OFF SWITCH
When set to "OFF", a full range signal is transmitted
regardless of the position of any isolator controls.
o HI PASS FILTER SWITCH
On each PGM is a Hi Pass Filter Switch. Pressing this
switch activates the high pass filter and when on the
indicator LED will illuminate. The cut off frequencies
for this filter can be adjusted by the SWEEP volume
rotary dial !1. If this switch is pressed simultaneously
with the Low Pass Filter switch the resulting effect is a
Notch Pass Filter.
!0 LOW PASS FILTER SWITCH
On each PGM is a LOW pass filter switch. Pressing this
switch activates the low pass filter for that PGM. When
on the indicator LED will be illuminated and this filter
will remove sound frequencies below the cut off point.
The cut off point can be adjusted by using the SWEEP
volume rotary dial !1. If this switch is pressed
simultaneously with the High Pass Filter switch the
resulting effect is a Notch Pass Filter.
!1 SWEEP VOLUME
This rotary dial is used to adjust the filter cut off points on
each PGM. A rotation to the left will result in a movement
away from the High frequencies towards the Low
frequencies. Vice versa a movement to the right will result
in a movement away from the Low frequencies towards the
High frequencies.
!2 C.F. ASSIGN SWITCH
Assigns the signals from each of the PGM channels to either
side of the crossfader or to MASRER OUT. There are three
positions;
A
⋯⋯⋯⋯The PGM is sent to the "A" position or left
position of the crossfader.
MASTER ⋯The PGM is sent directly to the master out.
B ⋯⋯⋯⋯The PGM is sent to the "B" position or right
side of the crossfader.
!3 CUE SWITCH
Sends a signal from each PGM to the monitor section for
headphone monitoring. When switch is on, an indicator
lights up.
!4 INPUT LEVEL VOLUME
Adjusts the Input level of each program. Typically this
fader is set to a position of 7-8. This fader is user
replaceable and may be changed easily by following this
users guide's instructions carefully. See "HOW TO
CHANGE THE FADER UNIT".
*Replace this fader with a Vestax IF-500 replacement
inputfader.
PROGRAM SECTION
Change to "CF-50"
q Remove the fader knob and 4 screws which fix the crossfader panel, and the carefully remove the panel. (See fig-e)
w Remove the 2 screws affixing the crossfader. (See fig-f)
e Carefully remove the multi-cable connector from the fader unit. (See fig-g)
r Remove the fader knob and the fader panel of the new CF-50. (See fig-h)
t Attach the fader panel to the new CF-50.
y Replace the fader unit making sure to that the connector wires are securely fastened before carefully positioning the fader unit
and affixing screws.
CROSS FADER
PMC-CX/E 04.4.26 10:16 AM ページ 7