Toshiba Blu-Ray Disc Player BDX1200KU User Manual
Page 18
1
E
ng
lis
h
[TV]
• [TV Screen]
Select the screen format according to
how you want the picture to appear on
the TV.
{16:9 Full} – for a disc with the aspect
ratio of 4:3, the output video is
stretched into 16:9 full screen.
{16:9 Normal} – for a disc with the
aspect ratio of 4:3, the output video is
resized vertically to match what will be
seen on the display.
{4:3 Pan&Scan} – for standard TV,
Display a wide picture on the entire
screen and cuts off the redundant
portions.
{4:3 Letterbox} – for standard TV,
Display a wide picture with two black
borders on the top and bottom of 4:3
screen.
• [Resolution]
Select a video output resolution that is
compatible with your TV display
capability.
{Auto} – Select the most suitable
resolution according to the TV .
{480i}, {480p}, {720p}, {1080i},
{1080p}
– Select a video resolution setting that
is best supported by the TV
. See TV
manual for details.
Note:
-When resolution is set to 720p/1080i/1080p:
(1) If only CVBS connected, the resolution of CVBS
video output will be set to 480i automatically.
(2) If HDMI and CVBS are both connected, there will
be no CVBS video output, instead, a message will be
shown as follows:
Out Of Range:Check Display Resolution
• [Color Space]
Select a predefined Color space of
picture.
{RGB} – Select RGB Color space.
{YCbCr} – Select YCbCr Color space.
{YCbCr422} – Select YCbCr422 Color
space.
{Full RGB} – Select Full RGB Color
space.
• [HDMI Deep Color]
This feature is available only when the
display device is connected by a HDMI
cable, and when it supports deep Color
feature.
{30 bits} – Output 30 bits Color.
{36 bits} – Output 36 bits Color.
{Off} – Output standard 24 bits Color.
Note:
- When the color space is "YCbCr422", even if HDMI
Deep Color is set to 30bits/36bits, it is not output
with Deep Color.
• [HDMI 1080
/24p]
{On} – Enable 1080/24p video
resolution setting.
{Off} – Disable 1080/24p video
resolution setting.
Notes about HDMI 1080/24p:
If you want the 24Hz output, it should fulfill below
3 conditions:
1.TV supports the 24Hz display;
2.Player choose the 24Hz option in the setup
menu;
3.Media must be the 24Hz video.
Notes:
- This resolution becomes effective only when
the playing Blu-ray Disc™ contents are Film
source.
- During HDMI 1080/24p playback, there will
be no composite output.
[Video Process]
TV
Video Adjust
More...
Low
Video Process
Motion Video...
Sharpness
Display Setting
SETUP Exit
Move cursor key to select menu option
then use “OK ” key to select
• [Video Adjust]
Select a predefined setting of the video.
1. Press OK .
2. Press/ to adjust the video
Brightness, Contrast, Hue and Saturation.
{Brightness} - press / to adjust
the brightness of display, goes left
means dark and right means bright.
{Contrast} - press / to adjust
the contrast of display, goes left
means low contrast and right means
high contrast.
{Hue} - press / to adjust the Hue
of display, goes left means low hue
and right means high hue.
{Saturation} - press / to adjust
the saturation of display, goes left
means low Saturation and right means
high saturation.