Tunturi F530 User Manual

Page 4

•

coming out of the handle bar and main beam tube.

Place the seat cushion on the seat plate, line up

the six bolts extending from the bottom of the seat

with the six holes on the seat plate. Using two

M8 nylock nuts, attach the seat to the seat plate

at the two front bolts. Align the four holes of the

handlebar with the four bolts of the seat cushion.

Secure the handlebar and the bottom seat cushion

using four M8 nylock nuts.

SEAT BACK

FIG.7

Install the seat back cushion onto the rear seat

bracket using four acorn nuts (closed end nut).

MAIN BEAM TUBE AND

FRONT ASSEMBLY

FIG. 8

Connect the wires from the main beam tube and

the front frame assembly. Attach the main beam

tube to the front frame assembly using four M8x20

bolts, two bolts on both sides.

NOTE !

Be careful

not to damage the wires!

U S E

CORRECT BODY POSITION

The Recumbent Cycle F 530 is designed to

comfortably distribute your weight evenly over

your buttocks and lumbar region of your lower

back. Your legs are also positioned closer to the

level of your heart, allowing a less strenuous and

more efficient cardiovascular workout. To ensure

proper positioning please follow the recommended

guidelines:

ADJUSTING THE SEAT TO

PEDAL DISTANCE

The lenght of the seat rail should be adjusted

so that your knee remains slightly bent (not

completely straight) when your leg is extended to

the furthest pedaling point forward. To adjust the

distance between the seat and the pedals: lift the

lever located below the seat to release the lock. To

extend the distance, push forward with your feet

in the pedals. Backpedal to find the comfortable

distance. To reduce the distance, pull the front

frame assembly using the scalloped handle next

to the left side crank. Push the lever back to

horizontal position to lock the attachment.

A S S E M B LY

TRANSPORT WHEELS

FIG. 1

Insert wheel couplers into front frame assembly,

secure each with an 4x15 screw. Push wheels onto

couplers and secure each with an M6x25 screw and

washer. Cover each bolt by pushing a green end cap

into hole at the center of each wheel.

METER

FIG. 2

Put two 1.5 V AA batteries into the battery holder

at the back of the meter, noting the + and - marks

on the bottom of the holder. Remove the wire

tying the meter wire on the bracket support tube.

Route the meter wire through the meter bracket.

Press the meter bracket into the bracket support

tube and line up the screw holes between the meter

bracket and the bracket support tube. Secure with

an M4x15L self-taping screw. Connect the meter

wire to the plug on the back side of the meter.

Tuck the wire inside the meter and carefully slide

the meter onto the meter bracket.

NOTE !

careful not to damage the meter wire! Remove the

protecting film from the display.

PEDALS

FIG.3

The pedals are distinguished by the markings R

and L on their shafts (R = right, L = left). Fasten

the right pedal to the right pedal crank turning

clockwise and the left pedal to the left pedal crank

turning counterclockwise. Fasten the pedal straps.

Choose the strap tightness, set the appropriate

strap hole on the retainer from below and pull

forcibly upward. The pedal straps are adjustable.

Especially when the device is new, the fastening of

the strap may seem relatively tight.

FEET

FIG.4

Insert a foot coupler into each side of rear frame

cross tube. Secure each with a 4x15 screw. Push feet

onto couplers.

MAIN BEAM TUBE

FIG. 5

Insure that the seat adjustment lever is in the

release (upward) position. Loosen the plastic

bushing at the back end of the main beam tube and

pull the pulse cable through the main beam tube

using the pulling string. Slide the main beam tube

through the seat frame assembly tube.

Place the plastic bushing around the pulse

cable and push the bushing back to its place in the

hole at the back of the main beam tube.

HANDLEBAR AND SEAT CUSHION

FIG.6

Position the handlebar so that it rests on the

supports of the seat plate. Connect the cables