Groupe SEB USA - T-FAL Digital Watch Babyphone & Watch Babyphone 912471 - Manual (Page 2)

1 – INSTALLING THE BABYPHONE
The BABYPHONE by TEFAL is
composed of 2 elements : a
transmitter which receives and
sends out sounds and which is to
be placed near the baby, and a
receiver which restores the
message at a distance and which
you must keep near you.
Installing the transmitter
• It must be connected to the
power network at all times.
The adapter (“transmitter” is
marked on its label) connects
under the
base of the
device; its
wire must
b e f u l l y
extended.
To ensure the relay in case of a
power failure, or to occasionally
use BABYPHONE where there is
no electricity, 4 AAA LR03 1.5 volt
alkaline batteries may be placed in
t h e d e v i c e . D u r i n g n o r m a l
operation, i.e. for 10 to 12 hours
per day, the batteries have a service
life of approximately 10 days.
Inserting the batteries :
- Disconnect from the power
network before inserting the
batteries.
- Open the back
of the device by
p r e s s i n g t h e
large button at
the top.
- I n s e r t a
screwdriver in
the slit of the
compartment
to unclip the
small cover.
- Turn the device over to remove
the black box
from its lodging
more easily.
- Position the
b a t t e r i e s i n
t h e b o x ,
matching the
+ and – marks
indicated (the negative end of the
battery is always placed on the
spring side).
- Reposition the black box in its
lodging.
- Clip on the cover.
- Reposition the
b a ck o f t h e
d e v i c e a n d
p r e s s t h e 2
parts together
until a “click”
is heard.
• The transmitter must be installed
at a certain height, in an upright
position, at a distance of 1 metre
m i n i m u m a n d 3 m e t r e s
maximum from the child.
• Put into operation by pressing
the 0/1 button.
ENG ENG
Installing the receiver
Th e WAT C H BA B Y P H O N E
model operates on alkaline
batteries, which are not supplied.
T h e D I G I T A L W A T C H
BABYPHONE model operates on
rechargeable batteries (already
inserted in the device).
• Putting the DIGITAL WATCH
BABYPHONE model into operation
When using for the first time,
the device must be recharged for
12 hours :
- Connect the adapter (“receiver”
is indicated on
its label) on the
left side of the
receiver.
- C o n n e c t t o
t h e p o w e r
network.
When putting the device into
operation, the battery indicator
of the digital display indicates the
battery charge level; when using
for the first time, it is important
that they be fully charged.
• Putting the WATCH BABY-
PHONE model into operation
Inserting the batteries :
- Open the rear shell of the
receiver by removing the two
screws with a screwdriver.
- P o s i t i o n 3
A A A t y p e
LR03 batteries
i n t h e b o x ,
matching the
+ and – marks
indicated on the battery box (the
negative end of the battery is
always placed on the spring side).
- Close and screw the rear shell
back down.
Warning : after the batteries have
been inserted, your device turns
on automatically.
1 2 3
Loudspeaker Visual
monitoring
Sound volume
adjustment On / off
button
Loudspeaker
Visual
monitoring
Sound volume
adjustment
On / off
button
Vibrator
button
Digital
display
Reception
indicator
Sound level
indicator
Batteries
indicator Vibrator
function
Selected
channel n°