Tech 21 SANSAMP PSA-1.1 - Manual (Page 12)

S PECIAL P AGE F UNCTION 6: S OFTWARE R EVISION N UMBER
This function tells you which version of software is in your SansAmp PSA. You cannot alter
this, but the information may come in handy in the future if software upgrades become avail-
able. When you select Special Page Function 6, the display will show a two-digit number.
After showing you the software version, the display will flash 00 to indicate you’re back in the
Special Page menu. You may now choose either a new Special Page function, or press Save
again to exit. If you don’t make a choice in about 15 seconds, the display stops blinking, indi-
cating the SansAmp PSA is in Program 00, bypass.
S PECIAL P AGE F UNCTION 7: E DIT P OT D ISPLAY M ODE
For finding presets, you can change how the information is displayed for a stored pot’s posi-
tion. You can choose to use digits, dashes or the numerical value of the pot. When you select
Function 7, the display will show either 00, 01 or 02.
00: Digits (as shipped)
01: Dashes
02: Numerical Value (0-127)
To change the setting, use the Up and Down buttons to select 00, 01, or 02. Then push Save
to store your selection. The display will then show a flashing 00 to indicate you’re back in the
Special Page menu. You may now choose either a new Special Page function, or press Save
again to exit. If you don’t make a choice in about 15 seconds, the display stops blinking, indi-
cating that the SansAmp PSA is in Program 00, bypass.
20
S PECIAL P AGE F UNCTION 8: D ISENGAGE A LL P OTS
This function renders all eight front panel potentiometers inactive. This advanced feature pre-
vents accidental setting changes during performances. All presets remain in the memory and
are accessible via MIDI, however, you cannot edit the programs while in this mode. Select
function 08 and press Save. Use the Up and Down buttons to select between two options:
00: All pots engaged (normal operation, as shipped)
01: All pots disengaged
Then push Save to store your selection. The display will then flash 00 to indicate you’re back
in the Special Page menu. You may now choose either a new Special Page function, or press
Save again to exit. If you don’t make a choice in about 15 seconds, the display stops blinking,
indicating that the SansAmp PSA is in Program 00, bypass.
S PECIAL P AGE F UNCTION 9: MIDI T HRU D ISABLE
This function disables MIDI Thru on the MIDI Thru/Out port. If you are using a multi-port
MIDI interface, you should disable MIDI Thru. If you are daisy chaining your MIDI devices,
leave it enabled. Select function 09 and press Save. Use the Up and Down buttons to select:
00: MIDI Thru enabled (normal operation, as shipped)
01: MIDI Thru disabled
Then push Save to store your selection. The display will then flash 00 to indicate you’re back
in the Special Page menu. You may now choose either a new Special Page function, or press
Save again to exit. If you don’t make a choice in about 15 seconds, the display stops blinking,
indicating that the SansAmp PSA is in Program 00, bypass.
21
Push
the
Save
Switch
Display
Shows
Software
Version
Automatically
Exits to
Special
Page Menu
After
15 Seconds,
or When
Save Switch
is Pushed
Display
Flashes 00
Upon
Return to
Special
Page
Menu
Digits Stop
Blinking
Upon
Return to
Program
00
Digits
Blink
Push
the
Save
Switch
Current
Setting
is
Shown
Select 00,
01 or 02
for
Display
Mode
Desired
Push
the
Save
Switch
Again
Display
Flashes 00
Upon
Return to
Special
Page
Menu
Digits Stop
Blinking
Upon
Return to
Program
00
Digits
Blink
Push
the
Save
Switch
Current
Setting
is
Shown
Select “o”
for
“Omni,”
or
Channel
1 - 16
Push
the
Save
Switch
Again
Display
Flashes 00
Upon
Return to
Special
Page
Menu
Digits Stop
Blinking
Upon
Return to
Program
00
Digits
Blink