Troy-Bilt 10030 - Manual (Page 19)

19
Safety & Decorative Labels
10 HP
®
D06572
777D06572
777I22047
PLACE ABOVE INGNITION
CUT OUT
STOP
STOP
10030
D06573
777D06563
777D06573
D00056
777S32065
DANGER
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS. USE CLEAN-OUT TOOL TO
UNCLOG DISCHARGE CHUTE.
DO NOT UNCLOG DISCHARGE CHUTE WHILE
ENGINE IS RUNNING.
SHUT OFF ENGINE AND REMAIN BEHIND
HANDLES UNTIL ALL MOVING PARTS HAVE
STOPPED BEFORE UNCLOGGING.
777S32066
DANGER
AVOID INJURY FROM
ROTATING AUGER - KEEP HANDS, FEET
AND CLOTHING AWAY.
KEEP AWAY FROM ROTATING IMPELLER
AND AUGER. CONTACT WITH IMPELLER OR
AUGER CAN AMPUTATE HANDS AND FEET.
USE CLEAN-OUT TOOL TO UNCLOG
DISCHARGE CHUTE.
DISENGAGE CLUTCH LEVERS, STOP ENGINE,
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
TO AVOID THROWN OBJECTS INJURIES,
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
READ OPERATOR'S MANUAL.
1.
2.
3.
4.
5.
DANGER
CLEAN-OUT TOOL
777D03165
751T642082100
Tecumseh Engine Labels
Top of plastic engine cover
above muffler vents in plastic
On plastic engine cover
left side of electric starter
On plastic engine cover
above primer knob
751T64141769 751T641393
AVERTISSEMENT
POUR VOTRE PROTECTION VEUILLEZ
LIRE ATTENTIVEMENT LES DIRECTIVES
SUR LA SECURITE ET L'ENTRETIEN
DANS LE MANUEL DU PROPRIETAIRE
2082
CAUTION
AVERTISSMENT
Muffler and adjacent surfaces are HOT. Do not touch.
Silencieux et surfaces adjacentes
TRES CHAUDES. Ne pas toucher.
El silenciador y las areas alredador estan CALIENTES. No tocar.
CUIDADO
TOUCH 'N TURN STEERING • ALL WHEEL DRIVE • ELECTRIC START • JUST ONE HAND ® OPERATION
D06574
777D06574
777I22052 777I22049 777I22053
I22052
CHUTE DIRECTIONAL CONTROL
CLOCKWISE TO DISCHARGE LEFT COUNTER CLOCKWISE TO DISCHARGE RIGHT
LEFT TURN CONTROL
AUGER CONTROL 6
1
2
F
3
4
5
R2
R1 R
CHUTE TILT CONTROL
I22049
IMPORTANT: THIS MACHINE IS EQUIPPED WITH AN
A U G E R C O N T R O L L O C K . TO STOP AUGER,
BOTH AUGER CONTROL AND TRACTION CONTROL
LEVERS MUST BE RELEASED.
TO STOP ENGINE, PULL OUT IGNITION KEY.
FOR STEERABLE OPERATION:
SQUEEZE LEFT TURN CONTROL TO STEER
SNOWTHROWER TO THE LEFT. SQUEEZE RIGHT TURN CONTROL TO STEER SNOWTHROWER TO THE RIGHT.
READ OPERATORS MANUAL BEFORE STARTING. INSERT IGNITION KEY INTO SLOT. MAKE SURE IT SNAPS INTO PLACE. DO NOT TURN KEY. RECOIL STARTER: PUSH PRIMER 2 OR 3 TIMES. ELECTRIC STARTER: DO NOT PRIME. PUSH START BUTTON OR PULL ROPE HANDLE TO START ENGINE. SELECT SPEED REQUIRED. SQUEEZE RIGHT TRACTION CONTROL LEVER TO MOVE. RELEASE TO STOP. ALWAYS RELEASE TRACTION CONTROL
LEVER BEFORE CHANGING SPEEDS.
FOR SNOWTHROWING, ENGAGE LEFT AUGER CONTROL LEVER BEFORE TRACTION CONTROL LEVER.
TRACTION
CONTROL
RIGHT TURN CONTROL
HEATED HANDLE GRIPS
ON OFF
TRACTION CONTROL
I22053