Transition Networks Substation-Rated Industrial Ethernet SUBTF10XX-1XX-MX - Manual (Page 13)

24
SIBTF10xx-1xx-Mx
24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Standard Description Compliance Level Remarks
IEEE1613, Power Substation Testing -- Continued
IEEE1613, Clause 7.3.2 Class 2 transverse mode
Class 1 common mode Surge fast transient
waveform – power AC
Class 2 transverse mode
Class 1 common mode Surge fast transient
waveform – power DC
Class 1 common mode Surge fast transient
waveform – relay port
Class 1 common mode Surge fast transient
waveform – Ethernet 10
Mbps
Class 1 common mode Surge fast transient
waveform – Ethernet 100
Mbps
IEEE1613, Clause 8 Class 2 Radio frequency
susceptibility
IEEE1613, Clause 9 Class 1 ESD contact discharge 8kV
EMC Type Tests -- Continued
Technical Specification -- continued
Troubleshooting
If the industrial switch fails, isolate and correct the failure by determining the answers
to the following questions and then taking the indicated action:
1. Is the “PRI” (primary power) LED illuminated?
NO
•
Ensure the power source is the proper voltage (48–170 VDC or 90–125
VAC, 50/60Hz).
• Ensure that the positive, negative, and ground wires from the power
source are properly connected to the primary inputs.
• Contact Technical Support: US/Canada: 1-800-260-1312,
International: 00-1-952-941-7600.
YES
•
Proceed to step 2.
2. (SIBTF10xx10x-MR models only) is the “AUX” (auxiliary power) LED
illuminated?
NO
•
If the device does not have an auxiliary power source, proceed to step 3.
• Ensure the power source is the proper voltage (48–170 VDC or 90–125
VAC, 50/60Hz).
• Ensure that the positive, negative, and ground wires from the power
source are properly connected to the auxiliary inputs.
• Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
YES
•
Proceed to step 3.
[email protected] -- Click the “Transition Now” link for a live Web chat. 25
Troubleshooting -- continued
3. Is the “FAULT” LED illuminated?
NO
•
Proceed to step 4.
YES
•
Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
4. For each port with a cable installed is either the “10MB” or the “100MB” LED
illuminated?
YES
•
Proceed to step 5.
NO
•
For each port with a cable installed and its LED is OFF, check the cable
for proper connection.
• For the fiber ports, verify that the TX and RX cables on the SIBTF10xx-
10x are connected to the RX and TX ports, respectively, on the device at
the other end of the fiber cables.
• Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600
5. For each RJ-45 port with a cable installed (ports 1, 2, 3, and 4), check to see if
the 10MB or 100MB LED is illuminated.
•
10MB is ON = The industrial switch has selected 10Mb/s operation.
• 100MB is ON = The industrial switch has selected 100Mb/s operation.
• If the speed is not correct, disconnect and reconnect the cable to restart the
initialization process.
• Proceed to step 6.
6. For each fiber port with a cable installed, is the “FD” (full-duplex) LED
illuminated?
NO
•
The industrial switch has selected half-duplex mode.
• If the mode is not correct, disconnect and reconnect cable to restart the
initialization process.
• Check the cable for proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
•
The industrial switch has selected full-duplex mode.
• If the mode is not correct, disconnect and reconnect cable to restart the
initialization process.
• Check the cable for proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.