Toshiba RAS-13JKVP-E - Manual (Page 6)

4 EN
REMOTE CONTROL AND ITS FUNCTIONS
a Infrared signal transmitter
Transmits signals to the indoor unit.
b button
Press the button to start operation. (A receiving beep is
heard.) Press the button again to stop operation. (A
receiving beep is heard.)
If no receiving sound is heard from the indoor unit, press
the button twice.
c Mode select button (MODE)
Press this button to select a mode. Each time you press
the button, the modes cycle in order from A: Auto
changeover control,
: Cool, : Dry, : Heat and back
to A.
(A receiving beep is heard.)
d Temperature button ( )
.. The temperature setting is increased to 30°C.
... The temperature setting is reduced to 17°C.
(A receiving beep is heard.)
e Fan speed button (FAN)
Press this button to select the fan speed. When you select
AUTO, the fan speed is automatically adjusted according to
the room temperature. You can also manually select the
desired fan speed from five available settings.
(LOW , LOW+ , MED , MED+ ,
HIGH ) (A receiving beep is heard.)
f Auto louver button (SWING)
Press this button to swing the louver. (A receiving beep is
heard.)
Press the button again to stop the louver from swinging. (A
receiving beep is heard.) (
) see page 14.)
g Set louver button (FIX)
Press this button to adjust the air flow direction. (A
receiving beep is heard.) (
) see page 14.)
h ON timer button (ON)
Use this button to change the clock and ON timer times.
To move up the time, press of the “ON ” button.
To move down the time, press of the “ON ” button.
i OFF timer button (OFF)
Use this button to change the OFF timer times.
To move up the time, press of the “OFF ” button.
To move down the time, press of the “OFF ” button.
j Reserve button (SET)
Press this button to store the time settings. (A receiving
beep is heard.)
k Cancel button (CLR)
Press this button to cancel the ON timer and OFF timer. (A
receiving beep is heard.)
l High power button (Hi POWER)
Press this button to start high power operation. ( ) see
page 16.)
m Memory button (MEMO)
Press this button to ready for storing the settings.
Hold down the button for more than 3 seconds to store the
setting indicated on the remote control and until the
mark is displayed. ( ) see page 13.)
n Automatic operation button (AUTO)
Press this button to operate the air conditioner
automatically.
(A receiving beep is heard.) (
) see page 16.)
o Economy button (ECO)
Press this button to operate the air conditioner
economically. (
) see page 16.)
p FILTER button
Press this button to turn off the filter cleaning indicator on
the indoor unit.
Press this button after cleaning the air filter. (
) see
page 19.)
q PRESET button
Press this button to operate the air conditioner according to
the settings stored using the MEMO button. (
) see
page 13.)
r Air purifying button (PAP)
Press this button to start the electrical air purifying
operation.
Press the button again to stop operation.
s Sleep timer button (SLEEP)
Press this button to start the sleep timer (OFF timer)
operation.
You can select the OFF timer time from among four
settings (1, 3, 5 or 9 hours).
TEMP
ON
ON
OFF
OFF
PAP AUTO
PRESET MODE
CLOCK
CHECK
FILTER
RESET
HiPOWER ECO MEMO
CLR SET
SWING FIX FAN SLEEP
ON OFF
a
b
r
d
e
c
l
g
f
k
h
n
q
m
o
s
j
p
i
TEMP
1.3.5.9H
01_EU_RAS-10JKP_EN.fm Page 4 Wednesday, April 9, 2003 8:08 AM