4220 multiplexer – Quick Eagle Networks 4220 User Manual

Page 3

Access Speed

Network Interface

Network Port

Line Rate

Connector Type

Line Code

Framing

Output Level

Input Level

System Timing

Drop-and-insert Interface

Line Rate

Connector Type

Line Code

Framing

Data Interface

Interface Types

DTE Port 1, DTE Port 2

Data Rates

Management Connectors

COMM Port

Ethernet

WAN Protocols

Power Requirements

Voltage

Consumption

Regulatory

Diagnostics

Loopback Tests

Loopback Control

Test Patterns

Network Alarms

Data port alarms

Front-panel LEDs

Physical

Dimensions

Weight

Environmental

Operating Temperature

Storage Temperature

Relative Humidity

Maximum Altitude

1 T1 ANSI 403 port
T1 (1.544 Mbps ± 50 bps)
100 ohm RJ-48C socket
AMI or B8ZS
D4 or ESF
0 db, -7.5 db, or -15 db LBO
0 to -26 db
Network, DTE, Aux, internal

T1 (1.544 Mbps ± 50 bps)
100 ohm RJ-48C socket
AMI or B8ZS
D4 or ESF

RS-449/EIA-530 or V.35
DB-25 socket
Nx56/64 kbps (N=1 through 24)

RJ-45 socket
RJ-45 socket

Frame Relay, Cisco-HDLC, and Protocol

transparent support

100 VAC to 240 VAC, 50-60 Hz or -40
VDC to -72 VDC (both on the same platform)

9 W maximum

FCC Part 15, FCC Part 68, UL 1950
Third Edition, Industry Canada CS-03
VCCI Class 1 CAN/CSA C22.2 No. 950-95

T1 network, T1 payload, fractional T1
payload, loop-up/loop-down commands, DTE

(full or fractional), NET/DTE

T1 set/reset codes, ESF FDL per
AT&T 54016 and ANSI T1.403 Annex B

1:1, 1:2, 1:4, 1:7, 3:24, QRW, all 0s, all 1s,

smart jack, two user-programmable 24-bit pat

terns, bit error injection

Net carrier loss, net sync loss, net AIS
received, net yellow received, CRC,
BPV, OOF threshold

RTS loss, DTR loss

Power/test, in-band, network status,
network loopback, loopback acknowledge,

DTE loopback, TD, RD,CTS, RTS, DTR

1 RU, rack mountable
22.3 cm (8.75 in ) W, x 33 cm (13 in) D, x 4.13

cm (1.63 in) H
2.27 kg (5 lbs.)

0º - 50º C
-20º - 60º C
0 - 95% non-condensing
4.6 Km (15,000 ft)

4220 Multiplexer

© 2007 Quick Eagle Networks. All rights reserved.
PDF/05/07
The information presented herein may change without notice
and should be used for informational purposes only. 4220
Access Multiplexer is a trademark of Quick Eagle Networks.

1 E1 G703/G704 port
E1 (2.048 Mbps ± 50 bps)
120 ohm RJ-48C socket or 75 ohm BNC
HDB3
ITU-T G.704/CTR 12
ITU-T G.703/CTR 12
0 to 20 dB
Network, DTE, Aux, internal

E1 (2.048 Mbps ± 50 bps)
120 ohm RJ-48C socket or 75 ohm BNC
HDB3
ITU-T G.704/CTR 12

RS-449/EIA-530, V.35, or X.21
DB-25 socket
Nx64 kbps (N=1 through 31) (structured),
32x64 kbps (unstructured)

RJ-45 socket
RJ-45 socket

Frame Relay, Cisco-HDLC, and Protocol

transparent support

100 VAC to 240 VAC, 50-60 Hz or -40
VDC to -72 VDC (both on the same platform)
9 W maximum

European harmonized standards 73/23 EEC,
91.31/EED, 89/336/EED, 93/68/EEC, and
91/263/EEC; UL 1950 3rd Ed.; CAN/CSA
C22.2 No. 950-95; Comision Federal de
Telecommunicaciones; CISPR 22 Level B (EN
55022), RoHS compliant

E1 network, E1 payload, fractional E1
payload, loop-up/loop-down commands,
DTE (full or fractional)

E1 set/reset codes

1:1, 1:2, 1:4, 1:7, 3:24, QRW, all 0s, all 1s, two
user-programmable 24-bit patterns, bit error
injection

Loss of signal, loss of frame, remote

alarm indication, alarm indication

signal, CRC4, CV, FE

RTS loss, DTR loss

Power/test, in-band, network status,
network loopback, loopback acknowledge,

DTE loopback, TD, RD,CTS, RTS, DTR

1 RU, rack mountable
22.3 cm (8.75 in ) W, x 33 cm (13 in) D, x 4.13

cm (1.63 in) H
2.27 kg (5 lbs.)

0º - 50º C
-20º - 60º C
0 - 95% non-condensing
3048 m (10,000 ft)