beautypg.com

QSC Audio PLX 1804 User Manual

Page 13

background image

13

Specifications PLX 1802, PLX 2502, PLX 3102, PLX 3602

PLX 1802

PLX 2502

PLX 3102

PLX 3602

OUTPUT POWER (Watts)

(1)

20 - 20k Hz, 0.05% THD, 8 ohms/Ch.

320

425

550

725

1k Hz, 0.1% THD (EIA), 8 ohms/Ch.

330

450

600

775

20 - 20k Hz, 0.05% THD, 4 ohms/Ch.

525

675

900

1100

1k Hz, 0.1% THD (EIA), 4 ohms/Ch.

575

750

1000

1250

1k Hz, 0.1% THD (EIA), 2 ohms/Ch.

900

1250

1550

1800

Bridge Mono, 20 - 20k Hz, 0.1% THD, 8 ohms

1100

1400

1900

2500

Bridge Mono, 1k Hz, 0.1% THD, 8 ohms

1200

1500

2100

2600

Bridge Mono, 1k Hz, 1.0% THD, 4 ohms

1800

2500

3100

3600

DISTORTION, SMPTE-IM

<0.02%, all models

FREQUENCY RESPONSE

20 - 20k Hz, ±0.5 dB, all models

SIGNAL to NOISE, unweighted, 20 - 20k Hz

-107 dB

-106 dB

-107 dB

-107 dB

VOLTAGE GAIN

31.9 dB

34.0 dB

35.0 dB

35.9 dB

INPUT SENSITIVITY, Vrms

for rated power into 8 ohms

1.28 (+4.4 dBu)

1.15 (+3.4 dBu)

1.23 (+4.0 dBu)

1.25 (+4.2 dBu)

OUTPUT CIRCUIT TYPE AB

AB/H

AB/H

AB/H

INPUT IMPEDANCE

10k ohms unbalanced, 20k ohms balanced

DYNAMIC HEADROOM

2 dB at 4 ohms

DAMPING FACTOR (8 ohms)

>500

AMPLIFIER PROTECTION

Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads

COOLING

Continuously variable speed fan; back-to-front air flow through heat sink array

CONTROLS

Front:

AC POWER switch, Gain controls (each channel) 21 detents

Back:

Input Configuration Switch (Stereo, Parallel, Bridge), Clip Limiters (On/Off)
Subwoofer Switch (100 Hz Low Cut/Full Range/100 Hz High Cut, each channel)
LF Switch (33 Hz Low Cut/Full Range, 1 each channel)

LED INDICATORS

POWER (blue), SIGNAL (green x 2), -10 dB (green x 2), CLIP (red x 2), BRDG (amber), PAR (amber)

CONNECTORS

Input:

1/4-inch TRS and female XLR; 20k ohm balanced, 10k ohm unbalanced

Output: Speakon connectors: Ch 1, 4-wires (Ch 1 + Ch 2); Ch 2, 2-wires (Ch 2 only)

Binding posts

LOAD PROTECTION

Turn-on/turnoff muting, DC fault blocking, Clip limiting, infrasonic filter (-3 dB at 5 Hz).

POWER REQUIREMENTS

Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.

DIMENSIONS

19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 13.9" (35.3 cm) D (from front mounting rails, including rear support
ears)

WEIGHT

(1)

21 pounds (9.5 kg) net; 26 pounds (11.8 kg) shipping

(1) NOTE: Due to special construction to meet EN-6100, CE models may have 5-12% (0.5 dBw) less power and 1.2 lb (0.6 kg) more weight.

U.S. patent no. 5767744 and patents pending

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE