Sylvania SST4274S - Manual (Page 3)

[-] GAME MODE [+]
OFF ON
[-] BRIGHT [+] [-] CONTRAST [+] [-] COLOR [+] [-] TINT [+] [-] SHARPNESS [+]
PREPARATION FOR USE
WATCHING A TV PROGRAM
1) Press the POWER button to turn on the TV.
2) Select the desired channel with the CH(annel)
▲ or ▼ button.
3) Adjust the volume to the desired listening level using the VOL(ume) ▲ or ▼ button.
4) Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)
SETTING THE SLEEP TIMER
The sleep timer function allows you to have the power automatically turn off
after a set time period.
1) Press the POWER button to turn on the TV and press the SLEEP button
on the remote control .
2) You may change the sleep time by pressing the SLEEP button on the
remote control repeatedly. The timer can be set up to 90 minutes. 10 min-
utes each time the SLEEP button is pressed. (The timer
display counts up and sleep timer will be displayed on the
screen when you press the SLEEP button on remote con-
trol.)
Note: When you disconnect the unit from the AC outlet or
when you have a power failure, the sleep time will be lost.
CLOSED CAPTION SELECTION
SLEEP 10
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [ C1]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [ C2]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [ T1]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [ T2]
TV SOUND [MAIN]
GAME MODE
Set to the most suitable position for video
games.
[+] : ON [ - ] : OFF
BRIGHT
Adjust until the darkest parts of the picture are
as bright as you prefer.
[+] : increase brightness [-] : decrease brightness
CONTRAST
Adjust to increase or decrease contrast.
[+] : increase contrast [ - ] : decrease contrast
COLOR
Adjust to be brilliant or pale color.
[+] : be brilliant color [ - ] : be pale color
TINT
Adjust to obtain natural skin tones.
[+] : greenish tone [ - ] : reddish tone
SHARPNESS
Adjust to detail in the picture.
[+]:increase sharpness [-]:decrease sharpness
Notes:
● “+” is achieved by pressing the VOL(ume)
▲ button and “-” by pressing the
VOL(ume)
▼ button.
● In the above steps, the picture adjustment
display will disappear from the TV screen
automatically after about 10 seconds if you
do not press any buttons. Press the MENU
and VOL(ume)
▲ button so that "PIC-
TURE" is selected. Then, press the
CH(annel)
▲ or ▼ button repeatedly until
the display returns to the screen.
● If you adjust another picture control after
you set Game mode to [ON], Game mode
will be set to [OFF] automatically.
[USING THE GAME BUTTON]
You may also set Game mode and select exter-
nal input mode at the same time by pressing
the GAME button on the remote control.
“GAME” appears on the TV screen.
● To exit Game mode and external input
mode, press the INPUT SELECT button on
the remote control.
● To cancel Game mode only, follow the steps
in “PICTURE ADJUSTMENT”. Game mode
will be set to [OFF] automatically and
“VIDEO2” (external input mode) instead of
“GAME” appears on the TV screen.
● If you press the GAME button when the TV
is off, the TV turns on and will be in Game
mode and external input mode automatically.
PICTURE ADJUSTMENT
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the VOL(ume)
▲ button so that "PICTURE" is selected.
3) Select the feature you wish to adjust with the CH(annel) ▲ or ▼ button and adjust it with the
VOL(ume) ▲ or ▼ button.
: Press the CH(annel) ▲ or ▼ button.
LANGUAGE SELECTION
If you want to change the language of the on-screen menu, follow the proce-
dure below.
1) Connect the power cord to a standard AC outlet.
Note: If some digits appear in the corner of the screen,
press the POWER button without unplugging the power cord.
2) Press the POWER button to turn on the TV.
3) Press the MENU button so that the menu display appears
on the TV screen.
4) Press the CH(annel) ▲ or ▼ button to point to "[ENG]".
5) Select "ENG(lish)", "ESP(añol)" or "FRA(nçais)" by using
the VOL(ume) ▲ or ▼ button.
6) Press the MENU button to exit the menu.
CHANNEL PRESETTING
To preset a channel or to change a preset channel, follow the procedure below.
1) Press the POWER button to turn on the TV.
2) Press the MENU button so that the menu display appears
on the TV screen.
3) Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then press the VOL(ume) ▲ button.
4) Press the CH(annel) ▲ or ▼ button to point to "AUTO PRESET CH".
Then press the VOL(ume) ▲ button.
The tuner scans and memorizes all active channels in your area.
● The TV distinguishes between standard TV channels and cable (CATV)
channels.
● When AUTO PRESET CH action is completed, the lowest memorized
channel reappears on the screen.
● When you press the CH(annel) ▲ or ▼ button after selecting AUTO PRESET CH,
the tuner will stop at the memorized channels only.
● The TV may recognize TV channels to be CATV channels by receiving conditions. In this case,
try AUTO PRESET CH action again in the fine receiving conditions.
● When AUTO PRESET CH is activated where there is no TV signal input, "NO TV SIGNALS"
will appear on the display after the completion of channel scanning.
[ADD/DELETE FUNCTION]
1) Press the MENU button so that the menu display appears on the TV
screen.
2) Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then press the VOL(ume) ▲ button.
3) Press the VOL(ume) ▲ button so that "ADD/DELETE" is selected.
4) Use the CH(annel) ▲ or ▼ button to select the channel you wish to put
into memory or to erase from memory.
Note: The menu will disappear automatically in about 10 seconds.
Perform "ADD/DELETE" function while this display appears on the
screen.
● Press the VOL(ume) ▲ or ▼ button to highlight the channel number
in LIGHT BLUE if you wish to add the channel into memory.
● Press the VOL(ume) ▲ or ▼ button to highlight the channel number
in LIGHT RED if you wish to erase the channel from memory.
5) Press the MENU button to exit the menu.
MTS (Multi-Channel Television Sound) SYSTEM
You can listen to a program in MTS stereo by following the steps below.
[To Select STEREO, MONO or SAP in Stereo broadcast]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel)
▲ or ▼ button to point to "TV SOUND".
3) Press the VOL(ume) ▲ or ▼ button to select your desired stereo mode.
([MAIN], [MONO] or [SAP].)
RESUME FUNCTION
If the power fails or is disconnected while the TV is powered on, the TV will turn on automatical-
ly when the power resumes.
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
ADD/DELETE
AUTO PRESET CH
ADD/DELETE
AUTO PRESET CH
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
OPERATIONS
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / F
V-CHIP SET UP
CAPTION [OFF
TV SOUND [MO
Type of
broadcast
Regular -None-
Stereo
broadcast
STEREO
SAP
Menu
Selection
MAIN MONO SAP
-None- -None-
MONO STEREO
SAP MAIN MAIN
To show the status, press the DISPLAY
button on the remote control.
SAP: Second Audio Program, which
means your program, can also be
received in a second language or
sometimes a radio station.
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MONO] PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [SAP]
: Press the VOL(ume) ▲ or ▼ button.
To cancel the sleep timer:
Press the SLEEP button repeated-
ly until "SLEEP 0" is displayed.
You may view specially labeled (cc) TV pro-
grams, movies, news and prerecorded tapes,
etc. with either a dialogue caption or text dis-
play added to the program. 1) Press the MENU button so that the menu
display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point
to "CAPTION".
3) Press the VOL(ume) ▲ or ▼ button to
select the mode you wish.
4) When done, press the MENU button to exit
the menu. : Press the VOL(ume) ▲ or ▼ button.