Ryobi RGT2500 - Manual

Install the spring over the
spindle. Insert each end of
the cutting line through the
eyelets in the cutting head
assembly and lower the
spool while feeding the line
as illustrated in Fig 16.
Once the spool is in place,
apply pressure on the spool
compressing the spring.
Pull each end of the line
sharply to unlock the line
from the slots. Continue to
apply pressure to the spool
until the knob can be
threaded clockwise onto
the spindle. Tighten the knob securely. Fig 17.
AIR FILTER
It is recommended that the air filter is cleaned on a regular
basis.To clean the air filter, depress the air filter cover
latch and remove the cover. Fig 18.
Remove and wash the filter with soap and water.
Allow to completely air dry before replacing the filter.
After replacing the filter secure the air filter cover.
CLEANING & STORAGE
WARNING: Always turn off your trimmer before
you clean or perform maintenance on it. Failure
to do so could result in serious personal injury.
Use a small brush to clean off the outside of the trimmer.
Do not use strong detergents on plastic housing or han-
dle, as they can be damaged by household cleaners that
contain aromatic oils such as pine or lemon and by sol-
vents such as kerosene. Wipe off any moisture with a soft
cloth.
STORAGE
If the trimmer will be stored for an extended period of
time, use the following storage procedure:
1. Drain all fuel from the fuel tank into a container.
2. Start the motor and allow it to run until it stalls. This
ensures that all the fuel has been drained from the
carburetor.
3. Allow the motor to cool. Remove the spark plug and
put
approximately 30ml of any high quality oil or 2
stroke oil into the cylinder. Pull the starter
rope slowly to distribute the oil. Reinstall the spark
plug. Leave the spark plug wire off
for storage.
4. Inspect for any damaged or loose parts. Repair or
replace any damaged parts and tighten loose screws,
nuts or bolts.
Fig 18 Cover
Latch
OWNER’S OPERATING MANUAL
GRASS TRIMMER
MODEL RGT2500
THANK YOU FOR BUYING A RYOBI TRIMMER.
Your new Trimmer has been engineered and manufactured to Ryobi's high standard for dependabili-
ty, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trou-
ble free performance.
CAUTION: Carefully read through this entire owner's manual before using your
new Trimmer.
Pay close attention to the Rules for Safe Operation, Warnings and Cautions. If you use your Trimmer
properly and only for what it is intended, you will enjoy years of safe, reliable service.
Thank You again for buying Ryobi tools.
SPECIFICATION
Motor..........................25cc 2 Stroke
Ignition........................Electronic
Carburetor ..................Diaphragm, all position
Cutting Head ..............Twin line bump feed
Cutting Line ................2.0 mm
Width Of Cut ..............43 cm
Fuel Mixture: ..............25:1
Weight ........................4.8 kg
Page 5
Fig 16
Fig 17
MELBOURNE: 960 Stud Road, Rowville, Vic, 3178,
Phone: (03) 9764 8655
HOBART: All Enquiries Phone: 1300 361 505
BRISBANE: All Enquiries Phone: 1300 361 505
PERTH: 33-35 Sorbonne Crescent, Canning Vale,
WA, 6155, Phone: (08) 9455 7775
ADELAIDE: All Enquiries Phone: 1300 361 505
TOWNSVILLE: All Enquiries Phone: 1300 361 505
Subject to the guarantee condition below, this Ryobi tool
(hereinafter called “the product”) is guaranteed by Ryobi
(hereinafter called “the Company”) to be free from
defects in material or workmanship for a period of 12
months from the date of original purchase covering both
parts and labour. Under the terms of this guarantee, the
repair or replacement of any part shall be the opinion of
the Company or its authorised agent. Should service
become necessary during the guarantee period, the
owner should contact the Authorised Ryobi Retailer
from whom the Product was purchased, or the nearest
Company Branch Office. In order to obtain guarantee
service, the owner must present the sales docket and
Guarantee Certificate to confirm date of purchase. This
product is sold by the dealer or agent as principal and
the dealer has no authority from the Company to give
any additional guarantee on the Company’s behalf
except as herein contained or herein referred to.
Guarantee Conditions
This guarantee only applies provided that the Product
has been used in accordance with the manufacturer’s
recommendations under normal use and reasonable
care (in the opinion of the Company) and such guarantee
does not cover damage, malfunction or failure resulting
from misuse, neglect, abuse, or used for a purpose for
which it was not-designed or is not suited; and no
repairs, alterations or modifications have been attempt-
ed by other than an Authorised Service Agent. This
guarantee will not apply if the tool is damaged by acci-
dent or if repairs arise from normal wear and tear.
The Company accepts no additional liability pursuant to
this guarantee for the costs of travelling or transporta-
tion of the Product or parts to and from the service deal-
er or agent - which costs are not included in this guar-
antee.
Certain legislation, including the Trade Practices Act,
1974 (as amended) and other state and territorial laws
give rights to the buyer and impose liability on the sell-
er in certain circumstances. Nothing herein shall have
the effect of excluding, restricting or modifying any con-
dition, guarantee, right or liability imposed, to the extent
only that such exclusion, restriction or modification
would render any term herein void.
THIS GUARANTEE FORM
SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
For your record and to assist in establishing date of purchase (necessary for in-guarantee service)
please keep your purchase docket and this form completed with the following particulars.
PURCHASED FROM _______________________________________________________
ADDRESS OF DEALER _____________________________________________________
DATE _________________MODEL NO ___________SERIAL NO ___________________
Present This Form With Your Purchase Docket When Guarantee Service Is Required
RYOBI TECHNOLOGIES AUSTRALIA PTY. LTD.
A.C.N. 002 277 509 Incorporated in N.S.W.
SYDNEY: 359-361 Horsley Road, Milperra, N.S.W.
2214, Phone: (02) 9772 2444
email: [email protected]
RYOBI TECHNOLOGIES NEW ZEALAND LIMITED
Auckland: 503 Mt Wellington Highway,
Mt Wellington, NZ, Phone: (09) 573 0230
email: [email protected]
RYOBI TECHNOLOGIES AUSTRALIA PTY. LTD.
GUARANTEE