Ryobi DP120 - Manual (Page 3)

3
RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and
understand this operator's manual and all labels affixed to
the tool. Safety is a combination of common sense, staying
alert, and knowing how your tool works.
READ ALL INSTRUCTIONS
■ KNOW YOUR POWER TOOL. Safe operation of this
power tool requires that you read and understand this
operator’s manual and all labels affixed to the tool. Learn
its applications and limitations as well as the potential
hazards.
■ GUARD AGAINST ELECTRICAL SHOCK by preventing
body contact with grounded surfaces such as pipes,
radiators, ranges, refrigerator enclosures.
■ KEEP GUARDS IN PLACE and in good working order.
■ REMOVE ADJUSTING KEYS AND WRENCHES. Get in
the habit - before turning on tool - that hex keys and
adjusting wrenches are removed from tool.
■ KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools
or pieces of wood on the machine while it is in operation.
■ DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools near gasoline or other flammable
liquids, in damp or wet locations, or expose them to rain.
Keep the work area well lighted.
■ KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or extension
cord while operating.
■ MAKE WORKSHOP CHILDPROOF with padlocks and
master switches or by removing starter keys.
■ DO NOT FORCE THE TOOL it will do the job better and
safer at the rate for which it was designed.
■ USE THE RIGHT TOOL FOR THE JOB. Do not force the
tool or attachment to do a job for which it was not designed
for. Use it only the way it was intended.
■ USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. Use only a cord heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. A wire gage size
(A.W.G.) of at least 16 is recommended for an extension
cord 25 feet or less in length. If in doubt, use the next
heavier gage. The smaller the gage number, the heavier
the cord.
■ DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry that could get
caught and draw you into moving parts. Non-slip footwear
is recommended. Wear protective covering over long hair.
■ ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact
resistant lenses; they are not safety glasses.
■ PROTECT YOUR LUNGS. Wear a face or dust mask if
the operation is dusty.
■ PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
■ SECURE WORK. Use clamps or a vise to hold the work
when practical. It’s safer than using your hand and frees
both hands to operate the tool.
■ DO NOT OVERREACH. Keep proper footing and balance
at all times.
■ MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions
for lubricating and changing accessories.
■ DISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, all tools should
be disconnected.
■ AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
■ USE RECOMMENDED ACCESSORIES. Consult this
operator’s manual for recommended accessories. The
use of improper accessories may cause risk of injury.
■ NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the bit is unintentionally contacted.
■ CHECK DAMAGED PARTS. Before using the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect
operation. A guard or other part that is damaged must be
properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
■ NEVER LEAVE TOOL RUNNING UNATTENDED, TURN
THE POWER OFF. Do not leave tool until it comes to a
complete stop.
■ DO NOT ABUSE CORD. Never yank the cord to
disconnect it from the receptacle. Keep the cord from heat,
oil, and sharp edges.
■ KEEP BITS CLEAN AND SHARP. Sharp bits minimize
stalling. Dirty and dull bits may cause misalignment of
the material and possible operator injury.
■ KEEP HANDS AWAY FROM WORK AREA. Keep hands
away from the bit. Restrain any loose clothing, jewelry, long
hair, etc. that may become entangled in the bit.
■ KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
■ STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
■ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON
AND OFF. Have defective switches replaced by an authorized
service center.