Rosewill RU101 - Manual

Power Protection UPS RU101/102 User Manual
RU-101/102
Rosewill Uninterruptible Power System (UPS) protects your computer hardware from physical
damage and will provide emergency battery backup power to prevent data loss in the event of
power problems.
The main features include
‹ Advanced equipment & data protection from blackouts, brownouts, sags, AC line noise and
surges.
‹ Full analytical high performance micro-processor control with true RMS synchronous
calculation.
‹ Intelligent battery management for battery status, battery power saving & battery
replacement control.
‹ DC direct start-up capability, complete diagnostic indication and control.
‹ Built-in USB communication port for RU102.
‹ Phone jack for phone and fax lines for RU102.
Specification
Model RU-101 RU-102
Capacity 600VA/300W 1000VA/500W
Input Voltage Range
120V +15%/- 20%
Output Voltage Range
120V +/-12%
Frequency 50 / 60 Hz auto sensing
Outlets 6 Outlets (3 Battery Backup & Surge)
Lighting / Surge Protection 480 Joules
Transfer Time to Battery/AC 4 ms (typical)
Battery Type Sealed and leak proof maintenance free lead-acid battery
Battery Specification 12V/5AH×1 12V/9AH x 1
Phone / Fax/ Network
Protection
W/O RJ11/RJ45
Short Circuit Protection Circuit breaker
Communication Port W/O USB
Operation Temperature +32℉ ~ 104℉ (0℃ ~ 40℃)
Operation Relative Humidity 0 to 95% non-condensing
Storage Temperature +5 ~ 113 ( ℉ ℉ -15 ~ 45 ) ℃ ℃
Net Weight 7.8 lbs 9.12 lbs
Dimensions (WxDxH) inch 6.1Ч4.3Ч8.3 7.1x6x9.5
Operation & Installation
Rosewill UPS can protect your equipment from all power problems such as surge, spikes,
blackouts, brownouts and line noise. When AC power is present and the ON/OFF switch is turned
on, Rosewill UPS continues to charge the battery and provide the power to the equipment directly
from the AC line. The battery can provide stable power to complete your work, save your data and
safely shut down your system when the utility power has failed.
Rosewill UPS is simple to operate and install. Following are the installation steps to connect he
equipment to the UPS.
1. Connect Rosewill UPS to grounded AC power Outlets.
2. Charge the battery at least 8 hours for a full charge before use.
3. Plug your computer and monitor into the “Battery Backup & Surge Protection” outlets. (These
outlets will provide emergency battery backup power during power problems as well as surge
protection from surge and spike.)
CAUTION: Do NOT plug LASER PRINTERS into any of the “Battery Backup” outlets.
CAUTION: Do NOT plug ACCESSORY SURGE STRIP into any of the “Battery Back & Surge
Protection” outlets.
4. Plug your peripheral equipment (printer, scanner, fax, speaker, etc.) into the “Surge
Protection” outlets. (These outlets will NOT provide battery backup power during a utility
power failure).
5. Switch on the Rosewill offline UPS product while the connected equipment is off,.
6. Turn on your connected equipment when the “AC mode” LED light is illuminated.
Troubleshooting
Symptom Possible Cause Action to Take
UPS is not turn on Switch on the On/Off switch. If the
power is not present, please make sure
your circuit breaker on the building is not
accidentally turned off. The UPS will not
turn on.
Circuit Breaker has
tripped. Reduce the amount of equipment
plugged into the “Battery Backup &
Surge Protection” outlets of the UPS.
Next, rest the circuit breaker by pushing
it back in.
The UPS is
making a
continuous sound
and the “Overload”
indicator is light. The “Battery Backup &
Surge Protection”
outlets are overload. Turn of the UPS and reduce the amount
of equipment connected to these
outlets.
Due to age the battery
does not hold a full
charge Removed all connected equipments
from the UPS and charge the battery at
least 8 hours. The UPS does not
provide expected
runtime.
Return for service or you can replace
the battery by ordering one new battery
The “Battery Backup &
Surge Protection”
outlets are overload. Refer to the Indicator Table “ UPS is
making a continuous sound and the
Overload indicator is light”
The UPS has
exhausted its available
run time. The UPS will turn off when the battery
has been depleted during the failure of
utility power. Allow UPS to re-charge
before continuing using of the UPS.
Connected equipment is
connected to the wrong
outlet. Ensure the equipment that you want to
stay powered during a failure of utility
power is plugged into the “Battery
Backup & Surge Protection” outlets.
Connected
equipments lose
power while
connected to the
Power the UPS.
The UPS may be faulty. Please Call your agency for further
troubleshooting.
Indicators
600VA/300W
1000VA/500W
1. On/Off Switch
This On/Off switch controls power to your equipment and performs a self-test to detect inverter,
line, battery status & LEDs.
NOTE: Turn on the UPS.
Press and hold the switch for more than two seconds and release the switch after the beep.
The UPS will start and provide the stable power to your equipments.
NOTE: Turn off the UPS.
Press and hold the switch for more than two seconds and release the switch. The UPS will
shut down completely.
NOTE: Perform Self-test.
The UPS will perform self-test for about 10 seconds when the UPS is turned on.
2. Line / Battery LED (Green LED)
Indicates the UPS is providing AC power to your equipment. When the LED is blinking the UPS is
providing power from the battery.
3. Warning LED (Red)