Remington MB-350 - Manual (Page 2)

2. Remove top cover panel using a flat-head screwdriver to gently pry panel free.
3. Remove 3 Phillips-head screws under top cover panel.
4. Remove top housing by gently prying housing sides free from clips.
5. Remove electrical housing from bottom housing.
6. Unclip bottom of electrical housing from top. Slide housing apart, exposing the
circuit board and batteries.
7. Clip wires connected to batteries to free them from the circuit board.
CAUTION: THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR
DISPOSED OF IN ACCORDANCE WITH STATE AND LOCAL REGULATIONS.
Do not burn or mutilate, as they may burst or release toxic materials. Do not
short-circuit, as this may cause burns.
The EPA-certified RBRC ® Battery Recycling Seal on the nickel-cad-
mium (Ni-Cd) battery indicates Spectrum Brands, Inc. is voluntary
participating in an industry program to collect and recycle these bat-
teries at the end of their useful life, when taken out of service in the
United States or Canada. the RBRC ® program provides a convenient
alternative to placing used Ni-Cd batteries into the trash or the municipal waste
stream, which may be illegal in your area. Please call 1-800-8-BATTERY SM for
information on Ni-Cd battery recycling and disposal bans/restriction in your area.
Spectrum Brands, Inc. involvement in this program is part of our commitment to
preserving our environment and conserving our natural resources.
NOTE:
■
Detach the groomer from the power supply cord before cleaning.
■ Do not use the groomer until it has dried.
1. Be sure Groomer is in Off position.
2. Remove Trimmer Guard Attachment. Shake or blow out accumulated hair.
3. Flip blade open by gently pushing upward on cutting teeth. Cutter assembly will
swing up, exposing and making accessible the assembly underside.
4. Blow out all lose hairs. Using the Cleaning Brush provided, remove remaining
hairs from cutting teeth and hair pocket.
OILING BLADES & CAUTIONS
■
Rinsing blades under water (above) requires lubricating the cutting blades 1x
monthly. Using only light-grade oils (e.g. sewing machine oil), simply spread 1-2
drops lightly over cutters with fingertip. Wipe away all excess.
■ Use only light-grade oils as these will not evaporate nor slow down speed of
cutting blades.
■ Do not use hair oil, grease, or any oil mixed with kerosene nor solvent as these
too will evaporate.
NOTE: Always recycle or properly dispose of batteries according to Local and
State requirements.
1. Unplug groomer from outlet to avoid risk of electrical shock.
TRIMMER GUARD ATTACHMENT
Remove Trimmer Guard Attachment to define hairline edges (e.g. sideburns,
nape of neck, beard \ mustache lines). Also, remove guard to clean cutter
assembly. To remove:
1. Be sure Groomer is in OFF position.
2. While holding Groomer in one hand, while holding Zoom Wheel with other hand,
gently pull Trimmer Guard Attachment away from Groomer.
3. Replace Guard by repeating steps #1 and #2. (NOTE: Guard can only be
placed on Groomer one way. If not fitting properly, simply remove and reverse).
FLEXING TRIMMER HEAD
The Grooming System is equipped with a locking switch to secure the flexing
trimmer head for detail trimming. To lock:
1. Be sure Groomer is in OFF position.
2. Be sure Trimmer Head is in natural “unflexed” position.
3. Slide Head Lock Switch downward. Should Trimmer fail to lock, simply unlock
switch, readjust Trimmer to its natural unflexed position, and reset lock.
4. To unlock Head, repeat step #1 followed by sliding Head Lock Switch upward.
How To Use
HAIR:
■
Should be dry and free of lotions or other liquids.
■ Comb outward to obtain maximum height/length and facing in the same direction.
BEARD:
■
When TRIMMING, add Trimmer Guard Attachment. For maximum control,
lock Trimmer Head to define lines. Front side of Groomer should be facing
away from face. Starting beneath chin, follow jaw line back toward ear with
upward motion. Allow Trimmer Guard Attachment to follow natural contours
of face. Trim either against or with the direction of beard growth, whichever is
preferred.
■ When THINNING or TAPERING, remove Trimmer Guard Attachment. Using the
Styling Comb, hold beard hairs in place while Trimming.
■ To Create the STUBBLE LOOK, add Trimmer Guard Attachment and set to
setting #1 or #2. While holding Trimmer horizontally, trim hairs by using an
upward or downward motion (against or with direction of hair growth, as
Grooming Tips
preferred). For an even closer Stubble Look, remove Trimmer Guard Attachment
altogether and repeat previous steps.
MUSTACHE:
■
Use Grooming Comb to first straighten hairs for trimming.
■ With Trimmer Guard Attachment removed and Trimmer Head locked, trim hairs
using an upward motion. After achieving desired length, use downward motion
to blend mustache hairs.
SIDEBURNS:
■
Use Grooming Comb to first straighten hairs for trimming.
■ With Trimmer Guard Attachment added and holding Groomer vertically, simply
trim using a downward motion.
NAPE OF NECK:
■
Using a hand-held mirror is necessary if self-trimming.
■ Remove Trimmer Guard Attachment and lock Trimmer Head for maximum
precision and control.
■ Lift hair off neck, using index finger to cover & protect those hairs NOT needing
trimming.
■ Carefully touch cutting blade to neck, slowly moving the groomer in an upward
direction until stopped by index finger.
Cleaning, Care & Maintenance
The Groomer is fitted with high-quality hardened steel or ceramic cutting blades
that are permanently lubricated. Cleaning should only be done with the soft
Cleaning Brush supplied. Always clean Grooming System attachments regularly
to ensure maximum performance and a proper operating life. Do not use liquid
cleaners on the cutters nor harsh corrosive chemicals on Grooming Body.
Groomer is washable by rinsing blades under running water. However, do NOT
submerge Grooming System in water. Blades must be lubricated again with Oil
supplied if Groomer is washed.
This warranty does not cover products damaged by the following:
■
Accident, misuse, abuse or alteration of the product
■ Servicing by unauthorized persons
■ Use with unauthorized accessories
■ Connecting it to incorrect current and voltage
■ Wrapping cord around appliance causing premature wear & breakage
■ Any other conditions beyond our control
No responsibility, obligation, or liability is assumed for the installation or
maintenance of this product.
SPECTRUM BRANDS, INC. SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE LIMITED IN
DURATION TO TWO YEARS FROM DATE OF ORIGINAL PURCHASE.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state or province to province. Some states do not allow
the exclusion or limitation of incidental, special or consequential damages.
Spectrum Brands, Inc. Money-back Offer
If within 30 days after you have purchased your Remington ® branded product,
you are not satisfied and would like a refund, return it with the sales slip indicat-
ing purchase price and date of purchase to the retailer from whom it was pur-
chased. Spectrum Brands, Inc. will reimburse all retailers who accept the product
within 30 days from the date of purchase. If you have any questions concerning
the money-back guarantee, please call 800-736-4648 in the US or 800-268-
0425 in Canada.
120 VAC 60 Hz
Questions or comments: Call 800-736-4648 in U.S. or 800-268-0425 in
Canada or visit www.remington-products.com
® Registered trademark of/Marque Déposée de ROVCAL, Inc.
©2008 ROVCAL, Inc. 05/08 Job# CS35470
Dist By: Spectrum Brands, Inc. 601 Rayovac Drive, Madison, WI 53711
MADE IN CHINA T22-26546
Limited Two-Year Warranty
Spectrum Brands, Inc. is a global consumer products company with a diverse
portfolio of world-class brands, including Remington-branded electric shavers.
Spectrum Brands, Inc. warrants this product against any defects that are due
to faulty material or workmanship for a two-year period from the original date
of consumer purchase. This warranty does not include damage to the product
resulting from accident or misuse.
If the product should become defective within the warranty period, we will
replace it free of charge. Return your product and sales receipt with your name,
address and day time phone number to: Spectrum Brands, Inc., Attention:
Consumer Services, 601 Rayovac Drive, Madison, WI 53711. For more informa-
tion call 800-736-4648 in the US or 800-268-0425 in Canada.
KEEP ORIGINAL SALES RECEIPT AS PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
Troubleshooting
Performance Guarantee
Q : WHAT IF THE CUTTERS DON’T MOVE WHEN TURNED ON?
A: The cutting unit may be dirty or clogged. Clean and lubricate the groomer as
described previously.
Q : WHAT IF THE GROOMER DOESN’T WORK AT ALL WHEN TURNED ON?
A: The groomer might simply need charging. Follow instructions for charging
as described previously. Should charging prove unsuccessful, contact customer
service at 1-800-736-4648 for assistance.
Q : WHAT IF THE GROOMER FAILS TO HOLD A CHARGE?
A: Fully discharge the groomer by running until completely stopping. Next, follow
recharging instructions described previously. If time between recharging cycles
fails to increase, the battery might require replacement. Contact customer service
at 1-800-736-4648 for assistance.
Battery Removal
This groomer is a washable appliance, the hand-held part of
which may be cleaned under water.
Contains a listed adaptor.
35470_MB350_IBA.indd 2 5/28/08 12:48:22 PM