Radio Shack DVD / VCR - Manual (Page 8)

– 8 – EN
Setup
Hint Hint
• To go back one step, press [s] (during
steps 2) to 7) ).
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint Hint
• If you accidentally select Spanish or French
and need English: Press [MENU] and
choose SELEC. IDIOMA or SELECTION
LANGUE. Press [B] and select ENGLISH.
Finally, press [CLEAR/C.RESET].
• To add or delete channels in this unit,
[SKIP/CH. G G /K K H/L L ] button works on
the channel number memorized in this
unit, [K
K /L L ] works on all.
Clock Setup
5 5
4 4
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
6 6
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7 7
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select the current year.
Select “AM” or “PM”.
8 8 To exit the CLOCK SET
screen
Select the current hour.
Select the current minute.
1 1 - M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
MENU
2 2
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
3 3
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
Select the current day.
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
VCR VCR VCR
VCR VCR
or
or
or
or
or
or
or
Preparation for Use
2 2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1 1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section on page 6.
• If your antenna is connected to an antenna ampli-
fier, the amplifier’s gain adjustment may need to
be temporarily reduced in order for Auto-Setup to
program all channels properly.
POWER
3 3
CH 01
AUTO SET UP
No No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized
in this unit by using [SKIP/CH. G G/K K H/L L]
(or [CHANNEL K K/L L]).
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press [B] once again.
Y Y es es Press [MENU]
to exit.
• Refer to “Hint for Cable Box or
Satellite Box” section on page 6.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
Turn on the Unit for the First
Time
TV Screen Remote Control
VCR VCR VCR
or
VCR VCR
NO
To Add or Delete Channels
1) Press [MENU] until the main menu
appears.
2) Select “CHANNEL SET UP” by
pressing [K/L]. Then, press [B].
3) Select “MANUAL SET UP” by
pressing [K/L]. Then, press [B].
4) Enter the desired channel number by
pressing [K/L] or
[SKIP/CH. G
G/K K H/L L].
5) Add or Delete it from memory by
pressing [s/B] so that “ADD” or
“DELETE” flashes on the TV screen
accordingly.
6) Exit the Preset mode by pressing
[CLEAR/C.RESET].
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2) Select “CHANNEL SET UP” by pressing
[K K/L L], then press [B].
3) Select “AUTO SET UP” by using [K K/L L],
then press [B]. After scanning, the tuner
stops on the lowest memorized channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Select “LANGUAGE SELECT” by pressing
[K K/L L], then press [B].
3) Select “ENGLISH” , “FRANCAIS” or
“ESPAÑOL” by pressing [K K/L L] , then press
[CLEAR/C.RESET] to exit.
To Select a Channel
You can select a channel by using
the Number buttons or
[SKIP/CH. G G/K K H/L L] .
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number. (For
example: 117, press [1], [1], [7])
• You must precede single-digit chan-
nel numbers with a zero (for example:
02, 03, 04 and so on).