Rolls RM65 - Manual (Page 3)

PAN: Adjusts the amount of relative signal to the Right, Left or both Main Out
jacks.
FX SEND: Controls the amount of signal (post-volume control) that is sent for that
channel to the FX Send jack.
MASTER CONTROLS
FX RETURN: Adjusts the amount of signal coming back into the FX Return jack.
MASTER VOLUME, RIGHT - LEFT: Controls the amount of signal sent out the
main Right and Left Output jacks, and sets the overall signal level except for the
Monitor Send jack.
REAR PANEL
CHANNEL 1
MIC
LINE TRIM
CHANNEL 2
MIC
LINE TRIM
CHANNEL 3
MIC
LINE TRIM
CHANNEL 4
MIC
LINE TRIM
CHANNEL 5
MIC
LINE TRIM
CHANNEL 6
MIC
LINE TRIM PHANTOM
POWER
AUX
BUSS IN
FX
SEND
FX
RETURN
MONITOR
OUT
RIGHT
OUT
LEFT
OUT
MODEL RM65
120 VAC
50/60 Hz 15 VA
SERIAL NUMBER
65-
MADE IN U.S.A. WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISQUE DE CHOC - NE PAS ENLEVER
C US
1 - 6 CHANNEL MIC INPUTS: XLR input connectors for mic or line level signals.
1 - 6 CHANNEL LINE INPUTS: 1/4” input connectors for line level signals.
TRIM: Adjusts the amount of input signal from the mic and line input jacks.
PHANTOM POWER: 6 switches for turning on the microphone phantom power for
the XLR inputs, and are numbered for the channel they are assigned to. DOWN is
on, UP is off.
AUX BUS IN: 1/4” TRS stereo input to the main mix bus, and may be used as an
auxiliary stereo input for joining two RM65s together.
FX SEND: 1/4” unbalanced jack for sending the signals assigned by each
channel’s FX Send control out to external effects.
FX RETURN: 1/4” unbalanced jack for inputting signals from external effects
devices.
MONITOR OUT: 1/4” unbalanced jack for sending signals assigned by each
channel’s monitor output control to an auxiliary amplifier or monitoring system.
RIGHT and LEFT OUTPUT: 1/4” TRS balanced jacks to be used as the unit’s
main outputs.
USING PHANTOM POWER
Phantom power is a means of powering condenser microphones through the
microphone cable. The RM65 has individually switchable 36 volts of phantom
power for each of its 6 channels through the XLR jacks. The DIP switches on the
rear of the unit are for switching the power on and off. When the little switch tab is
down, the power is on. The number on the switch corresponds to the channel that
is receiving the power. If phantom power is not needed, it should be switched off
to avoid possible damage to a microphone, or degraded sound quality.
SPECIFICATIONS
Input Impedance: 600 W balanced
50K W unbalanced (1/4")
Output Impedance: 50 W TRS Balanced
Max Input Level: -15 dBV XLR 600 W
+18 dBV 1/4"
Phase Shift: < 10 deg. 20 Hz - 20 kHz
Phantom Power: 36 V DC
Input Connectors: XLR and 1/4"
Outputs: 1/4" main balanced +17 dB max
1/4" monitor +17 dB max
1/4" FX send
Max Gain: (Mains) 60 dB mic
26 dB line
(Monitor) 55 dB
Tone controls: 20 dB treb, bass cut/boost, 400 Hz center
Max S/N Ratio: 106 dB
THD < .003%
IMD (SMPTE) < .003%
CMRR 52 dB
Power 120 VAC 50-60 Hz, 15 W
Weight: 7 lbs (3KG)
Size: 19" x 1.75" x 6.5" (48cm x 4.5cm x 17cm)
NOTES:___________________________________________________________
2 5