NAD C 542 - Manual (Page 7)

GB
7
The following example presents a step-by-step illustration of how to
program and start Program Play to play tracks 5, 23, 9, 16, and 1.
While the CD player is stopped:
Press on remote control Display shows
PROGRAM Pr p:01
5 5 p:01
PROGRAM Pr p:02
+10, +10, 3 23 p:02
PROGRAM Pr p:03
9 9 p:03
PROGRAM Pr p:04
+10, 6 16 p:04
PROGRAM Pr p:05
1 1 p:05
PROGRAM Pr p:06
PLAY
The Calendar display track listing will indicate the selected
program.
The coil springs should contact the (-) end of each cell. Push the
battery compartment cover back and press gently until it latches.
In some cases, corrosion or fingerprint oil on the battery contacts
may cause poor operation. Remove both cells, rub the metal
contacts at both ends of each cell with a clean cloth or a pencil
eraser, and re-install the cells, being careful to orient them
correctly.
Developed by Pacific Microsonics in the USA, HDCD ® (High
Definition Compatible Digital ® ) is a patented encode/decode
process for delivering the full richness and detail of the recording.
HDCD ® encoded CDs sound better because they are encoded with
20-bits of real musical information, as compared to 16-bits for all
other CDs. HDCD
® overcomes the limitation of the 16-bit CD
format by using a sophisticated system to encode the additional
four bits onto the CD while remaining completely compatible with
the existing CD format.
The result is a larger dynamic range, a more focused 3-D
soundstage, and natural vocal and musical timbre. An HDCD-
encoded disc played on the HDCD-equipped NAD
C 542 CD player
produces audibly superior clarity and depth. Enhanced
performance will also be obtained from standard CDs.
The NAD C 542 CD player will automatically identify an HDCD ®
encoded disc and activate its HDCD ® decoder. The red indicator
will light up when it’s playing an HDCD ® encoded disc.
CD-R & VD-RW AUDIO DISCS
The
C 542 can play back CD-R, CDRW audio discs that have been
recorded on a computer or CD-recorder. The quality of CD-R,
CD-RW audio discs varies widely which may affect playability.
Some factors that affect playability:
• The quality of the disc itself. Generally speaking, CD-R, CD-RW
blanks from well-renowned companies give better results
than unbranded ones.
• The quality of CD-recorder or computer CD re/writer. Some
recorders and writers produce better results than others.
• The CD-R & CD-RW was created with high-speed writing. In
7. To terminate program play, press STOP. However the stored
track list remains in memory; if you want to play the program
again, simply press PLAY again. If you want to edit the program,
press PROGRAM repeatedly to review the list and change. To
add tracks, press the PROGRAM button until the highest
program number is displayed.
8. To clear the program memory, press STOP twice, OPEN/CLOSE
to open the drawer, or switch off the POWER.
DELETE
The
C 542 CD Player allows to user to delete unwanted tracks in
any desired order in either the Program Mode or the Stop Mode.
To Delete tracks, use the sequence of commands below.
In Program Mode:
1.
2.
3.
4.
5.
6.
Press DELETE. The display indicates "dE d:01"; the player is
now ready for first Delete entry. "dE" will change to first
memory track after 1 second.
Use the
SKIP & SKIP buttons to select the first
track you would like to delete. The track number will flash.
Press DELETE again to store the selected track number in
memory. The selected track number will be deleted in the
display. The display will advance to next location. This
showing that the player is ready for your second entry.
Repeat Steps 2 and 3 to select the delete the track numbers
in memory, up to a maximum of 20 entries but cannot delete
track above track 25.
To play the stored program, just press PLAY. During playing,
the SKIP buttons will access only the tracks still listed. The
deleted songs are not listed.
To clear the memory, press STOP twice, OPEN/CLOSE to
open the drawer, or switch off the power.
In Stop Mode:
1.
2.
3.
4.
Press DELETE. The display indicates "dE d:01" with total
track time. The player is ready for the first Delete entry.
Use the Direct-Entry Numeric keypad buttons to select the
first track you would like to delete. The selected track
number will be deleted in the calendar display and the
updated total playing time is shown on display.
Repeat Steps 2 to select the track numbers you would like to
delete, up to a maximum of 25 entries but cannot delete
track above track 25.
To play the remaining tracks, just press PLAY. During playing,
the SKIP buttons will access only the tracks still listed. The
deleted songs are not listed.
5. To clear the memory, press STOP, OPEN/CLOSE to open the
drawer, or switch off the power.
NOTE: In the Program-entry mode, the SKIP and
buttons have a “wrap-around” function: if you SKIP Back
repeatedly from Track 01, the number counts down from the final
track on the disc. This provides a convenient way to select high-
numbered tracks.
INSTALLING AND REPLACING BATTERIES
The remote control requires two 1.5-volt AAA-size (i.e. UM-4 or
IEC RO3) cells. Alkaline cells are recommended, to obtain
maximum operating life. To open the battery compartment, place
your fingertip in the recess on the rear of the remote control, push
against the flexible edge of the battery cover and lift the cover
upwards. Install fresh cells, orienting them as shown on the
diagram within the compartment.
The Calendar display will indicate remaining track listing. After
completing playback, the
C 542 will automatically stop, and the
display will again show all the tracks contained on the inserted
CD.