Napoleon Fireplaces EF38H - Manual (Page 5)

5
W415-0330 / B / 03.25.04
By opening the top louvres with the louvre tabs you can
access the manual controls for the fireplace.
1. Power - activates power to the fireplace. Must be on for
the fireplace to work.
2. Manual Control - activates buttons 3, 4 & 5.
3. Fire Log Accent Light - switches the light on and off that
illuminates the fireplace. (Can be used as a Nite Lite).
4. Flame Effect and Speed - switches the flame on. Re-
peated pressing of the switch cycles the flame through
speeds 1 to 4 and off.
5. Fan / Heater - turns the fan and heater on and off.
6. Thermostat - Controls the temperature of the area.
To increase the temperature, turn the dial clockwise.
The heater may emit a slight, harmless The heater may emit a slight, harmless The heater may emit a slight, harmless The heater may emit a slight, harmless The heater may emit a slight, harmless
odour when first used. This odour is a odour when first used. This odour is a odour when first used. This odour is a odour when first used. This odour is a odour when first used. This odour is a
normal condition caused by initial heat- normal condition caused by initial heat- normal condition caused by initial heat- normal condition caused by initial heat- normal condition caused by initial heat-
ing of ing of ing of ing of ing of internal hea internal hea internal hea internal hea internal heater par ter par ter par ter par ter parts ts ts ts ts. T . T . T . T . Ther her her her hereaf- eaf- eaf- eaf- eaf-
ter ter ter ter ter, any odour is normally the r , any odour is normally the r , any odour is normally the r , any odour is normally the r , any odour is normally the result esult esult esult esult
of household dust settling on the of household dust settling on the of household dust settling on the of household dust settling on the of household dust settling on the
heater element. heater element. heater element. heater element. heater element.
This fireplace is supplied with a infrared remote control.
This remote control operates with an arc of 50º and has
to be pointed at the infrared eye for it to work. (See fig. 1)
This procedure is required every time the power is turned
off, or lost to the unit.
1. Turn on the power button of the hand held remote con-
trol. If there is no beep, access the front control panel.
2. To access the control panel, open the louvres with the
louvre tabs.
3. Make sure that the main power switch 1 of the front con-
trol panel is turned on.
4. Repeat step #1.
A - Main power on/off : Activates the power to
the firelace from the remote control.
B - Fire Log Accent Light: To illuminate
the fireplace.(Can be used as a Nite Lite)
C - Flame effect and speed: 1,2,3,4, off.
D - Fan/Heater on/off: Turns the fan
and heater on and off.
E - Sound (optional)
Batteries NOT included. Batteries NOT included. Batteries NOT included. Batteries NOT included. Batteries NOT included.
Two AA batteries required.
Two AA batteries required. Two AA batteries required. Two AA batteries required. Two AA batteries required.
Note
C
D
B
E
A
1 2 3 4 5
6
MAINTENANCE
If you notice the flame look is darker on one side of the
fireplace, check the light bulbs to ensure that one has not
burned out.
Bulb must be replaced with a MAX 60 watt incandescent
clear light bulb.
1. Replace the bulb, turn the circuit breaker off or unplug
the appliance.
2. Remove the front facia.
3. Detach the light access panel by removing the four
screws.
4. Replace the burned out light bulb using a new 60 watt
clear incandescent bulb.
Light Access Panel
OPERATION
MANUAL CONTROLS
REMOTE CONTROL INITIALIZATION
USAGE OF THE REMOTE CONTROL
BULB REPLACEMENT
FIGURE 1
Infrared Eye
5. Replace access panel and front facia.
6. Turn on the power or plug the appliance back in.
7. Turn on the main power and test.
Manual Controls