Nikon VT650 User Manual

Quick connect guide, Remote control features connections, Step 2

CANCEL

SELECT

POWER

STATUS

/STAND BY

SOURCE

AUTO

ADJUST

Quick Connect Guide

Remote Control Features

Connections

INPU

DIO

-CO

S-VID

VID

RGB INPUT

RGB OUTPUT

Step 2

Connect the supplied power cable.

Step 3

Turn on the projector.

Step 4

Set up the Projector.

To adjust the projector’s focus or to zoom in and out use
the Focus ring or Zoom lever on the lens.
To optimize image, press the AUTO ADJUST button on
the cabinet or the remote control.

For older Macintosh computers, use a
commercially available pin adapter to
connect to your Macintosh’s video port.

Power down all equipment
before making connections.

Power button

NOTE: To turn off the projector,
press and hold the POWER button
for a minimum of two seconds.

Adjusting the T

ilt Foot

1 Press and hold the T

ilt button on the front of the

projector .

2 Lift the front edge of the projector to the desired

height, and release the button to lock the

Adjust-

able T ilt Foot.

Printed in China

7N8P1131

Step 1

Connect the supplied 15pin-15pin signal cable.

Monitor

RGB

INPUT

OUT

-C

ONT

S-V

IDEO

VID

Zoom lever

Focus ring

SELECT

POWER

STATUS

/OFF

SOURCE

AUTO

ADJUST

INP

-CO

NTR

S-V

IDE

VID

Brightness

Contrast

Color

Hue

Sharpness

Normal

Zoom

Wide Zoom

Cinema

SELECT

POWER

STATUS

/STAND BY

SOURCE

AUTO

ADJUST

INP

TPU

PC-C

TRO

S-V

IDE

VID

• To fine-tune the image’s position vertically on the screen,

rotate the foot. Each of the rear feet height can be changed
up to 0.6” (4mm).

• If the projected image does not appear square to the screen then use keystone correction for proper adjustment.

LECT

SOURCE

AUTO

ADJUST

INP

TPUT

-C

TRO

S-V

IDEO

VID

NTER

LEC

WER

STA

TUS

/OFF

SOU

30˚

Remote sensor on the
remote mouse
receiver

NOTE: If you are using a Macintosh computer, you can click either
the right-click or left-click button to activate the mouse.

Infrared T

ransmitter

Direct the remote control toward the remote sensor on the projector cabinet.

LED

Flashes when any button is pressed.

Power ON Button

If the main power is applied, you can use this button to turn your projector on.

Power OFF Button

If the main power is applied, you can use this button to turn your projector off.

NOTE: To turn off the projector, press and hold the POWER OFF
button for a minimum of two seconds.

VIDEO Button

Press this button to select a video source from a VCR, DVD player,
laser disc player or document camera.

S-VIDEO Button

Press this button to select an S-Video source from a VCR.

RGB Button

Press this button to select an RGB source from computer or com-
ponent equipment connected to your RGB port.

Auto Adjust

Button

Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly, or in some
cases it may take some time for a source to switch between sources.

Menu Button

Displays the menu.

Select (

) / (mouse) Buttons

When you are in the Computer mode, these buttons work as a computer mouse.
When you are in the Projector mode, which is indicated by lighting the PJ button:

Use these buttons to select the menu of the item you wish to adjust.

: Use these buttons to change the level of a selected menu item.

Enter (Left click) Button

When you are in the Computer mode, this button works as the
mouse left button.
When you are in the Projector mode, which is indicated by light-
ing the PJ button:
Use this button to enter your menu selection. It works the same
way as the “Enter” button on the cabinet.

Cancel (Right click) Button

When you are in the Computer mode, this button works as the
mouse right button.
When you are in the Projector mode, which is indicated by light-
ing the PJ button:
Press this button to exit “Menus”. It works the same way as the
“Cancel “ button on the cabinet.

PJ Button

Press this button to switch the Select, Cancel, and Enter buttons
between the Projector mode (lit red)and the Computer mode. Press
this button or any one of the Power ON/OFF, Menu, Help and Mag-
nify buttons to switch to the Projector mode and the PJ button lights
red. To switch back to the Computer mode, press the PJ button again.

Picture Button

Press this button to display the Picture adjustment window.
Each time this button is pressed, the current picture adjustment
item will change as follows:

Unavailable items will be skipped.

Aspect Button

Press this button to display the Aspect Ratio select window.
Each time this button is pressed, the current aspect ratio will
change as follows:

You can also select the aspect ratio by using the Select or
button. If no adustments are performed within 3 seconds, the As-
pect Ratio select window will disappear. (See also page E-32.)

Help Button

Provides information about the current signai and the status of
the projector.

Freeze Button

This button will freeze a picture. Press again to resume motion.

Picture Mute Button

This button turns off the image and sound for a short period of
time. Press again to restore the image and sound.

Magnify Button

Use this button to adjust the image size up to 400%.

V olume Button

Press (+) to increase the volume and (–) to decrease it.

NOTE: The default is the Computer mode, which allows you to use
the Select, Cancel, and Enter buttons as your computer mouse.
When the POWER ON/OFF, MENU, HELP or MAGNIFY button is
pressed, the PJ button lights red to indicate that you are in the Pro-
jector mode. If no buttons are pressed within 10 seconds, the light
goes out and the Projector mode is canceled.

OFF

VIDEO S-VIDEO

RGB

POWER

MAGNIFY

SELECT

M NU

18
17

AUTO ADJ.

FREEZE PIC-MUTE

PICTURE

VOLUME

HELP

ASPECT

You can use the supplied wireless remote
control and remote mouse receiver
to operate your PC mouse wirelessly from
across the room. See page E-14.

Connecting the remote
mouse receiver to your
computer.

To USB port of
PC or Macintosh

To Mouse(PS/2)
port of PC

Attach the supplied
PS/2 Adapter