NAD Blu-ray Disc Player T557 - Manual (Page 8)

IDENTIFICATION OF CONTROLS
front panel
1 StandbY: Press this button to switch ON the T 557. The display window
will illuminate. If there is disc loaded, the display window will show the
playback time status of the disc. If there is no disc loaded, the VFD will
briefly show “NO DISC” and thereafter show the default display “HOME”.
Pressing the [ ] button of the BR 2 will switch ON the T 557 from
standby mode and at the same time open the disc tray. The T 557
can also be switched ON by pressing the [ON] or [ ] buttons of the
remote control. Pressing the standby button again turns the unit back
to standby mode. Unplug the AC power cord from the AC wall socket to
completely shut down the T 557.
2 diSc traY: With the DISC TRAY open, insert a Blu-ray disc (BD), DVD,
CD or other compatible media disc face down onto the tray.
“Check Disc” appears at the On-Screen Display (OSD) (“ERROR” at the
VFD), if the disc is placed upside down (and it is a single sided disc). The
disc tray will then automatically open.
3 vacuum fluoreScent diSplaY (vfd): If there is disc loaded, the
display window will show the elapsed playback time of the current
track/file/chapter (and track number; applicable for CD playback only).
If there is no disc inside, the display window will show “HOME”.
4 remote SenSor: Point the BR 2 at the remote sensor and press the
buttons. Do not expose the remote sensor of the T 557 to a strong light
source such as direct sunlight or illumination. If you do so, you may not
be able to operate T 557 with the remote control.
distance: About 23 ft (7 m) from the front of the remote sensor
angle: About 30° in each direction of the front of the remote sensor
5 open/cloSe: Press this button to open and close the disc tray.
6 plaY/pauSe: This dual-function button alternates between starting
and stopping playback. Press this button to toggle between Play and
Pause of a BD, DVD, CD or other compatible media disc. Press to start
play or resume play after Pause. If the disc tray is open, press this button
to automatically close the tray and start playback if a CD disc is loaded.
During playback, press this button to stop playback temporarily,
keeping the optical pickup at its current position on the disc. To resume
playback at the exact point where it stopped, press [PLAY/PAUSE] again.
7 Stop: Except for BD playback, pressing this button will stop and at
the same time pause playback of the disc. Press [PLAY/PAUSE] button
to resume play from the spot it was stopped. For BD playback, pressing
the [STOP] button will fully stop the playback and will return you to the
TITLE or MENU option of the disc.
8 uSb input: Connect an external USB device into this input. Refer also
to the “USB MODE” section of “USING THE T 557 – FEATURES” under the
“OPERATION” main heading.
9 home: Press to access all the media for playback and setup of the
T 557. Refer also to the “USING THE HOME MENU” section of “USING THE
T 557” under the “OPERATION” main heading.
10 [ ] , [ ], enter: Press [ ] to skip forward or [ ]
to skip backward a track, file or chapter.
Press [ ] to scan fast-forward or fast-reverse during playback.
Each time the button is pressed, the speed increases until the maximum
level is reached. The scanning speed is indicated by trailing icons or
as shown in the OSD and may vary by disc type. The speed will be
retained even after the button is released; press [PLAY/PAUSE] to resume
normal playback.
The front panel [ ] , [ ] and ENTER buttons
respectively simulate the same functions of the [ ] and ENTER
buttons of the BR 2 remote control under the following conditions or
options only
• Navigating through the HOME menu and SETUP menu.
• Select through MOVIE, MUSIC or PHOTO files as contained in a disc.
Outside of the above conditions, the [ ] and [ ]
buttons normally function as SKIP and SCAN modes.
NOTE
Not all media support maximum speeds for scanning.
4 5 6 7 8 9 10 2 3 1
8
EN
G
LIS
H
FR
A
N
Ç
A
IS
ES
PA
Ñ
O
L
IT
A
LIA
N
O
D
EU
TS
CH
N
ED
ER
LA
N
D
S
SV
EN
SK
A
РУ
СС
К
И
Й