Profile SP62 - Manual (Page 2)

I
NTRODUCTION
1
P
ARTS LIST
TEMPLATE
GRILLES
SPEAKER WIRES
LENGTH: 3m (9’ 10”)
RETAINING CLIPS
MOUNTING
SCREWS
SIZE: 4 x 20mm
SP62
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1/2" 2-Way
Woofer Cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Treated Paper
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1"
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foam
Maximum Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Watts
Nominal Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5~40 Watts RMS
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ohms
Magnet Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Oz.
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 dB/W/m
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ~ 20,000 Hz
Piezo
S
PECIFICATIONS
Congratulations on your purchase of a Profile state-of-the-art speakers. Your selection of a
Profile car audio product indicates a true appreciation of fine musical reproduction. Whether
adding to an existing system or including your Profile speakers in a new system, you are certain
to notice immediate performance benefits.
Before mounting the speakers, select a location that allows for at least 49mm (1 15/16”) of
mounting depth. The speaker inside the door must not come in contact with the window when
rolled down. Additionally, the speaker should be out of the way of window cranks and door
handles allowing for normal operation.
I
NSTALLATION
IMPORTANT!: THE LARGER HOLE ON
THE CLIP SHOULD BE ON THE FRONT
SIDE OF THE PANEL AND THE SMALLER
SPILT HOLE SHOULD BE ON THE BACK
SIDE OF THE PANEL.
CUT OUT SPEAKER MOUNTING AREA
THEN DRILL SCREW HOLES USING
3.3mm (5/32”) BIT.
INSERT RETAINING CLIP OVER HOLE
IN DOOR PANEL.
USE THE ENCLOSED TEMPLATE
TO MARK THE CUT OUT AREA
AND DRILL HOLES. IF HOLE
EXISTS SKIP TO STEP .
TO RADIO OR AMPLIFIER
BLACK
STRIPED WIRE SOLID
COLOR WIRE
CONNECT SPEAKERS.
MOUNT SPEAKERS AND SNAP ON GRILLES.
IF YOU ARE MOUNTING SPEAKERS IN THE
VEHICLE’S FACTORY LOCATIONS, GRILLES
ARE NOT NEEDED.
2
124mm (4 7/8”)
3.3mm (5/32”)
I
NTRODUCTION
1
P
ARTS LIST
TEMPLATE
GRILLES
SPEAKER WIRES
LENGTH: 3m (9’ 10”)
RETAINING CLIPS
MOUNTING
SCREWS
SIZE: 4 x 20mm
SP62
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1/2" 2-Way
Woofer Cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Treated Paper
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1"
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foam
Maximum Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Watts
Nominal Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5~40 Watts RMS
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ohms
Magnet Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Oz.
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 dB/W/m
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ~ 20,000 Hz
Piezo
S
PECIFICATIONS
Congratulations on your purchase of a Profile state-of-the-art speakers. Your selection of a
Profile car audio product indicates a true appreciation of fine musical reproduction. Whether
adding to an existing system or including your Profile speakers in a new system, you are certain
to notice immediate performance benefits.
Before mounting the speakers, select a location that allows for at least 49mm (1 15/16”) of
mounting depth. The speaker inside the door must not come in contact with the window when
rolled down. Additionally, the speaker should be out of the way of window cranks and door
handles allowing for normal operation.
I
NSTALLATION
IMPORTANT!: THE LARGER HOLE ON
THE CLIP SHOULD BE ON THE FRONT
SIDE OF THE PANEL AND THE SMALLER
SPILT HOLE SHOULD BE ON THE BACK
SIDE OF THE PANEL.
CUT OUT SPEAKER MOUNTING AREA
THEN DRILL SCREW HOLES USING
3.3mm (5/32”) BIT.
INSERT RETAINING CLIP OVER HOLE
IN DOOR PANEL.
USE THE ENCLOSED TEMPLATE
TO MARK THE CUT OUT AREA
AND DRILL HOLES. IF HOLE
EXISTS SKIP TO STEP .
TO RADIO OR AMPLIFIER
BLACK
STRIPED WIRE SOLID
COLOR WIRE
CONNECT SPEAKERS.
MOUNT SPEAKERS AND SNAP ON GRILLES.
IF YOU ARE MOUNTING SPEAKERS IN THE
VEHICLE’S FACTORY LOCATIONS, GRILLES
ARE NOT NEEDED.
2
124mm (4 7/8”)
3.3mm (5/32”)