Philips AX 1100/00 - Manual (Page 5)

RESUME
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD). Use
the RESUME–HOLD–OFF slider for these functions.
1 Switch the slider to RESUME during playback to
activate RESUME.
y
RESUME is shown.
2 Press 9 whenever you want to stop playback.
3 Press 2; whenever you want to resume playback.
y
RESUME is shown and playback continues from
where you have stopped last.
• To deactivate RESUME, switch the slider to OFF.
y
RESUME goes off.
HOLD
You can lock the buttons of the set by switching the
slider to HOLD. Now, when a key is pressed, no action
will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated,
you can avoid accidental activation of other functions.
1 Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLd is shown when
you press any button. If the set is switched off,
HoLd
will be shown only when 2; is pressed.
2 To deactivate HOLD, switch the slider to OFF.
Note: If you deactivate HOLD by switching the slider to
RESUME, you will be activating the RESUME
function.
p /L IN E OU T
OF F RE SU ME HO LD
p /L IN E OU T
OF F RE SU ME HO LD
nF diSC indication
– CD-RW (CD-R) is not recorded
• Use FINALIZE on the properly. CD recorder to complete the recording
HoLd indication and/or no reaction to controls
– HOLD is activated
• Deactivate HOLD
–
Electrostatic discharge
• Disconnect the set from power supply or take out the batteries for a few seconds
The CD skips tracks
– The CD is damaged or dirty
• Replace or clean the CD
–
RESUME , SHUFFLE or PROGRAM is active
• Switch RESUME , SHUFFLE or PROGRAM off
No sound or bad sound quality
– PAUSE is activated
• Press 2;
– Loose, wrong or dirty connections
• Check and clean connections
–
Volume is not adjusted
• Adjust the volume
–
Malfunctions due to nearness of active mobile phones
• Keep the player away from active mobile phones
–
Strong magnetic fields near the player
• Change the player’s position or connections
p /L IN E OU T
TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or
service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this
will invalidate the guarantee. Do not open the set as there is a risk of
electric shock!
No power, playback does not start
Batteries
–
Batteries inserted incorrectly
• Insert the batteries correctly
–
Batteries are empty
• Change the batteries
–
Contact pins are dirty
• Clean them with a cloth
Mains adapter
–
Loose connection
• Connect the adapter securely
no diSC indication
– The CD is badly scratched or dirty
• Replace or clean the CD
–
CD is not or incorrectly inserted
• Insert a CD, label upwards
–
The laser lens is steamed up
• Wait until the lens has cleared
MODE
It is possible to play tracks in random order, to repeat a
single track or the entire CD.
1 Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
y
SHUFFLE : All tracks of the CD are played in random
order until all of them have been played once.
y
SHUFFLE REPEAT ALL : All tracks of the CD are played
repeatedly in random order.
y
REPEAT : The current track is played repeatedly.
y
REPEAT ALL : The entire CD is played repeatedly.
2 Playback starts in the chosen mode after 2 seconds.
• To return to normal playback, press MODE repeatedly
until the display shows no active modes.
MODE
PROGRAM