Peavey Max 450 - Manual (Page 8)

8
S SY YS ST TE EM M S SP PE EC CIIFFIIC CA AT TIIO ON NS S::
Mains Fuse = 8 amps
Mains Voltage = 120 VAC 60 Hz
Power Consumption = 350 watts
Hum and noise: Typically greater than -89 dB unweighted with
controls set as follows…
Pad = Passive
Bright = Normal
Pre gain = 5
Contour = 0
Low = 0
Mid = 0
Mid Shift = 1kHz
High = 0
Volume = 5
P PO OW WE ER R A AM MP PLLIIFFIIE ER R S SE EC CT TIIO ON N::
P PR RO OT TE EC CT TIIO ON N::
Electronic current limit protection circuit.
Thermal protection circuit.
D.C. crowbar protection circuit.
DDT speaker protection circuit with defeat switch.
Variable speed fan, thermally controlled
G GE EN NE ER RA ALL IIN NFFO OR RM MA AT TIIO ON N::
Minimum load = 2 Ohms
Input sensitivity: 1.0 VRMS
Two 1/4" speaker jacks in parallel
R RA AT TE ED D P PO OW WE ER R O OU UT TP PU UT T::
450 Watts (30.00 V RMS) into 2 Ohms
300 Watts (34.64 V RMS) into 4 Ohms
170 Watts (36.88 V RMS) into 8 Ohms
T TY YP PIIC CA ALL P PO OW WE ER R O OU UT TP PU UT T
475 Watts (30.82 V RMS) into 2 Ohms
with no more than 1% THD+N
308 Watts (35.10 V RMS) into 4 Ohms
with no more than 1% THD+N
177 Watts (37.63 V RMS) into 8 Ohms
with no more than 1% THD+N
N NO OIIS SE E::
Typically greater than 102 dB below full power @
8 Ohms unweighted
D DD DT T D Dy yn na am miicc R Ra an ng ge e::
Typically greater than +15 dB
FFR RE EQ QU UE EN NC CY Y R RE ES SP PO ON NS SE E::
+0/-0.61 dB, 100mW to 160 W RMS, 20 Hz to 20 kHz
(8 Ohm load, typically below 0.2% THD+N)
P PR RE EA AM MP PLLIIFFIIE ER R S SE EC CT TIIO ON N::
S SE ET TT TIIN NG GS S FFO OR R M ME EA AS SU UR RE EM ME EN NT TS S U UN NLLE ES SS S O OT TH HE ER RW WIIS SE E N NO OT TE ED D::
Pad = out (Passive)
Bright = out (Normal)
Pre-Gain = 5 (12 o’clock)
Contour = 0 (fully counterclockwise)
Bass = 0 (12 o’clock)
Mid = 0 (12 o’clock)
Mid Shift = 0 (12 o’clock)
High = 0 (12 o’clock)
Master Volume = 10 (fully Clockwise)
Line Out Level = 10 (fully Clockwise)
IIN NP PU UT T S SE EN NS SIIT TIIV VIIT TY Y ((LLe evve ell tto o a acch hiie evve e ffu ullll p po ow we err))::
With Pad Out...
Nominal input: 100 mV RMS
Minimum input: 9 mV(pre gain and master fully CW)
Maximum input: 3.0 V(maximum signal at input before
clipping occurs)
W Wiitth h P Pa ad d --110 0 d dB B iin n::
Nominal input: 315 mV RMS
Minimum input: 28 mV (pre gain and master fully CW)
Maximum input: 9 V (maximum signal at input before
clipping occurs)
E EQ QU UA ALLIIZ ZA AT TIIO ON N::
Bright boost: + 8 dB @ 5 kHz
Contour: Special frequency compensation
Bass: ± 15 dB @ 30 Hz, Shelving type Eq
Mid : ± 15 dB @ 200 @ 2 kHz (Mid shift control determines
center frequency)
Mid Shift: 200 to 2 kHz
High: ±15 dB @ 8 kHz, Shelving type Eq
T TU UN NE ER R S SE EN ND D::
Instrument level through a buffer
LLIIN NE E O OU UT T::
-∞ to -10 dB (for nominal input).
Level is dependent on level control setting and pre gain setting
E EFFFFE EC CT TS S LLO OO OP P::
Set for -10 dB (0.315 V RMS) with pre @ 5, Master @ 10
Controlled via footswitch, ground tip to defeat.
P PR RE EA AM MP P O OU UT TP PU UT T::
1 V RMS nominal
M MA AX X ® ® 4 45 50 0
S SP PE EC CIIF FIIC CA AT TIIO ON NS S