Philips AJ3121/05 - Manual

1
3 6
4
5
0
#
2
8
9
7
!
@
Clock Radio
Register your product and get support at
www.philips.com/welcome
1
INSTALLATION
POWER SUPPLY
1 Check if the power supply, as shown on the type plate located on the bot-
tom of the set, corresponds to your local power supply. If it does not, consult
your dealer or service center.
2 Connect the power cord to the wall outlet.
3 To disconnect the set from the power supply completely, remove the
plug from the wall outlet.
For users in the U.K.: please follow the instructions on the left
CLOCK MEMORY BACKUP
The clock memory backup allows your alarm and clock time settings to be stored
for up to a day when there is a power interruption e.g. power failure. The com-
plete clock radio and display illumination will be switched off. As soon as the
power supply returns, the display will indicate the correct time.
1 Remove the battery door to insert a 9 volts 6F22 type battery (not included)
for backup.
2 Replace the battery door.
NOTE: If no backup battery is installed or the power interruption is prolonged, you
will need to set the clock and alarm times again.
Batteries contain chemical substances so they should be disposed of
properly.
English
Congratulations on your purchase and welcome to Philips!
To fully benefit from the support that Philips offers, reg-
ister your product at www.philips.com/welcome.
CONTROLS (see fig. 1 )
1 SET TIME /ALARM SET
- sets the clock time
- sets the alarm time
2 HR / MIN
- adjusts the hours / minutes for clock / alarm / sleep time
3 REPEAT ALARM / SLEEP OFF
- switches off the active alarm for a 9 minutes period
- switches off the radio sleep function
4 ALARM RESET
- stops the active alarm for 24 hours
5 SLEEP
- activates the radio for sleep function
- adjusts the sleep period
6 TUNING - tunes to radio stations
7 ALARM indicator - lights up when alarm is activated.
8 FM/MW - selects FM/MW waveband
9 VOLUME - adjusts the sound level
0 RADIO / ALARM
OFF: switches off the radio/alarm
RADIO ON: switches on the radio
ALARM - RADIO: activates the radio for alarm
ALARM - BUZZER: activates the buzzer for alarm
! Power cord - connects to wall outlet
@ Pigtail - improve FM reception
# Battery door - opens to store a 9 volts 6F22 battery (not included) for clock
memory backup.
User manual
AJ3121
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type
of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should
have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution
board should not be greater than 5 Amp.
Note: The severed plug must be disposed of to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral
(N), brown = live (L). As these colours may not correspond with the colour mark-
ings identifying the terminals in your plug, proceed as follows:
• Connect the blue wire to the terminal marked N or coloured black.
• Connect the brown wire to the terminal marked L or coloured red.
• Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped over
the sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956
and The Performer’s Protection Acts 1958 to 1972.
Printed in China AJ3121_05_UM_V2.1
Meet Philips at the Internet
http://www.philips.com
AJ3121
W
English
AJ3121_05 2010.1.11 16:27 Page 1