Philips DVDR3350H - Manual (Page 2)

1 Connect 2
Set up
Start with the ‘Basic Connection.’
If you have a VCR, follow the instructions for ‘Connection with a VCR or similar device’.
~
MAINS ANTENNA
TV
EXT 1
VIDEO (CVBS)
AUDIO
S-VIDEO (Y/C)
AUDIO
AUDIO
R
L PB
OUT 2
VIDEO (CVBS)
OUT 1
Y
PR
COAXIAL DIGITAL AUDIO OUT
L
R
S-VIDEO
(Y/C)
AUDIO
AUDIO
R
L
OUT 2
VIDEO
(CVBS)
OUT 1
Television (rear)
To antenna
or set-up box
Philips recorder
(rear)
A Connect the antenna cable to the
ANTENNA jack on the recorder.
B Use the supplied RF coaxial cable to connect the
TV jack on this recorder to the Antenna In
jack on the TV.
C Use the supplied audio/video cable (yellow plug)
to connect the VIDEO (CVBS) -OUT 2 jack
on this recorder to the VIDEO IN jack on the TV.
D Use the supplied audio/video cable (red/ white
plugs) to connect the AUDIO L/R OUT 2 jack
on this recorder to the AUDIO IN jacks on the
TV.
E Connect the power cable from the recorder to
an AC power outlet.
EXT 1
AUDIO IN
L
R
VIDEO IN (CVBS)
~
MAINS ANTENNA
TV
EXT 1
VIDEO (CVBS)
AUDIO
S-VIDEO (Y/C)
AUDIO
R
L
OUT 2
VIDEO (CVBS)
L
R
AUDIO
PB
OUT 1
Y
PR
COAXIAL DIGITAL AUDIO OUT
Television (rear)
Philips recorder
(rear)
To antenna
or set-up box
VCR or similar device
(rear)
A Follow steps A to E of ‘Connecting’ under ‘Basic
Connections’ to connect the recorder before you
proceed to step
B below.
B Use a yellow video cable (not supplied) to
connect the VIDEO (CVBS) EXT 1 jack on this
recorder to the yellow VIDEO OUT jack on the
VCR.
C Use another red and white audio cable (not
supplied) to connect the AUDIO L/R EXT 1
jacks on this recorder to the red and white
AUDIO OUT jacks on the VCR.
D Connect the power cable from your VCR to an
AC power outlet.
Note In this setup, the VCR cannot record TV
programs.
For additional connection diagrams, see the
accompanying User Manual.
A Inserting batteries
* Note where the positive and negative ends go.
B Finding the viewing channel
A Press STANDBY-ON on the recorder
B Switch on the TV.
Note If connected to your VCR, make sure it
is switched off or in standby mode before
proceeding.
C Press SETUP .
D Press ‘0’ on the TV’s remote control,
then press the Channel Down button
repeatedly until you see the { SETUP
MENU - GENERAL } page. This is the
correct viewing channel for the recorder.
Note You may press the AV or SELECT button
on the TV’s remote control (if available) to select
the correct viewing channel. See your TV’s user
manual.
Remote control
(back)
STANDBY-ON
SETUP MENU - GENERAL
To exit, press [SETUP].
Record Quality
Auto Chapter Marker
Auto Program
Manual Program
SP
Search
Edit
5min.
Your Philips recorder is now ready for use!
Basic Connection
A Before Connecting
Unplug the antenna cable that is currently connected
to your TV.
B Connecting
Connection with a VCR
or similar device
A Before Connecting
Your new Philips recorder replaces the VCR for
your recording needs. First, unplug all the
connections from your VCR.
B Connecting
C Initial installation
A Press SETUP on the remote control.
Record Quality
Auto Program
Manual Program
SP
Search
Edit
Auto Chapter Marker 5min.
SETUP MENU - GENERAL
B Setup and install TV channels.
Highlight and press RIGHT . Press
DOWN repeatedly until you highlight
{ Auto Program - Search } and press OK .
A warning message will appear. Select OK OK and
press OK to proceed.
Highlight { Tuner Input Source } , press RIGHT
and select a suitable setting:
– { Cable } if the recorder is connected via a cable/
satellite box.
– { Air } if the recorder is connected directly to the
antenna wall outlet.
Select OK CONTINUE and press OK to start automatic TV
channel search.
Note If no channels were found, check the
antenna connection and start the channel search
again.
C Select the language.
Highlight and press RIGHT .
– select the System Language
– select the Audio Language for DVD disc playback.
– select the Subtitle Language for DVD disc playback.
– select the Disc Menu Language for DVD disc
playback.
D Set the date and time
Highlight and press RIGHT .
Highlight { Date-Time Setting} and press
RIGHT . Select { Auto } and press OK .
A warning message will appear. Select OK OK and
press OK to proceed.
– The date and time settings will follow broadcast
channel information of Program Number 1.
E
Press SETUP to fi nish installation.
Philips recorder (front panel)
3
Enjoy
(The TSB in playback mode)
About the Time Shift
Buffer (TSB)
Once you switch on this recorder, the currently
selected TV program will be stored in a temporary
storage called the ‘TSB’ (Time Shift Buffer). The TSB
can store up to 3 hours of recordings temporarily.
Press once to display the Time Shift video bar.
10:15:36 AM
08:30:45 AM
07:15:36 AM
CH003
The contents on the time shift buffer will be erased
once you press CH
or or if you
switch to another mode: SOURCE ,
DV , DVD REC .
Start time
of program
Program stored
in TSB
Shows TV channel or
video input source
TSB
status icon
in playback
Time of current
screen playback
Instant Replay
While watching a live TV program, you can press
LEFT
to jump back 10 seconds upon every
single press for instant replay.
To return to live broadcast, press and hold
RIGHT .
Pause ‘live’ TV
At times, you may be interrupted while
watching your favourite program. Now you
can PAUSE it, as if you were in control of the
broadcast.
A Press PAUSE while watching any live TV
program to suspend it.
B Press PLAY to continue.
C To return to live broadcast, press and hold
RIGHT .
To jump forward playback, press RIGHT once
for every 30 seconds.
Start Recording
A Before recording to hard disk
You can preset the recording quality for content
recorded to the time shift buffer.
A Press SETUP on the remote control.
B
Highlight and press RIGHT .
Press DOWN repeatedly until you highlight
{ Record Quality } and press RIGHT .
C Use UP / DOWN to select the preferred
mode of recording quality and press OK to confi rm.
Hours of Recording
that can be stored
Record Quality
17
34
42.5
51
68
102
HQ High Quality
SP Standard Play
SP+ Standard Play Plus
LP Long Play
EP Extended Play
SLP Super Long Play
80GB Hard Disk
Values are estimates only. Parts of the HDD storage will be
reserved for the operations of this recorder and time shifting.
B Record to hard disk
A
Press TUNER to switch to tuner mode.
B Press CH or to go to the TV program
channel you wish to record.
C Press to display the time shift video bar.
10:15:36 AM
LIVE
07:15:36 AM
Note To record from a connected external
device, press SOURCE repeatedly to cycle
through video input sources from:
{ CAM 1 } : VIDEO jack on the front
{ CAM 2 } : S-VIDEO jack on the front
{ EXT 1 } : EXT 1 jack on the back
or Press DV to record from a DV camcorder
connected via the DV IN jack on the recorder.
D Press REC to start recording.
Note Press REC repeatedly to extend 30
minutes increments per single press.
E To stop recording, press STOP .
Current
time