Pioneer PRS-D4000F - Manual

Thank you for purchasing this PIONEER
product. It is designed to give you many
years of enjoyment.
PIONEER SUGGESTS USING A PRO-
FESSIONAL INSTALLER DUE TO THE
COMPLEXITY OF THIS PRODUCT.
Please read all instructions and WARN-
INGS in this manual before attempting
operation. Should you have any questions,
contact your nearest Pioneer authorized
dealer or installation specialist.
Information to User
Alteration or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.
Important
The serial number of this amplifier is writ-
ten on the bottom of the unit. For your
own security and convenience, write it
down on the enclosed warranty card. Keep
the card handy for future reference.
Product registration
Visit us at the following site:
1 Register your product. We will keep the details of
your purchase on file to help you refer to this
information in the event of an insurance claim
such as loss or theft.
2 Receive updates on the latest products and tech-
nologies.
3 Download owner’s manuals, order product cata-
logues, research new products, and much more.
Before Using This Product
After-sales service for Pioneer
products
Please contact the dealer or distributor from where
you purchased the product for its after-sales ser-
vice (including warranty conditions) or any other
information. In case the necessary information is
not available, please contact the companies listed
below:
Please do not ship your product to the companies
at the addresses listed below for repair without
advance contact.
7 U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
7 CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION
DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R OP2
1-877-283-5901
For warranty information please see the Limited
Warranty sheet included with your product.
CAUTION
Never replace the fuse with one of greater
value or rating than the original fuse. Use
of an improper fuse could result in over-
heating and smoke and could cause dam-
age to the product and injury including
burns.
CAUTION
Do NOT install or use your Pioneer ampli-
fier by wiring speakers rated at 4 Ohm (or
lower) in parallel to achieve a 2 Ohm (or
lower) bridged mode (Diagram B).
Amplifier damage, smoke, and overheating
could result from improper bridging. The
amplifier surface could also become hot to
the touch and minor burns could result.
To properly install or use a bridged mode
for a two-channel amplifier and achieve a 4
Ω load, wire two 8 Ω speakers in parallel
with Left + and Right – (Diagram A) or
use a single 4
Ω speaker. For a four-chan-
nel amplifier, follow the speaker output
connection diagram for bridging as shown
on the back of your amplifier, and wire
two 8
Ω speakers in parallel to achieve a 4
Ω load or use a single 4 Ω speaker per
channel.
If you have any questions or concerns,
please contact your local authorized
Pioneer dealer or call Pioneer customer
service.
WARNING
• Handling the cord on this product or cords associ-
ated with accessories sold with the product will
expose you to lead, a chemical known to the State
of California and other governmental entities to
cause cancer and birth defects or other reproduc-
tive harm. Wash hands after handling.
• Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
• Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also, do
not touch the amplifier when it is wet.
• For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
• Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
• To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
• Contact the dealer if you cannot detect the cause.
• To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
• Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
• DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface and
the surface of any attached speakers could become
hot to the touch and minor burns could result.
Diagram A - Proper
8
Ohm
Speaker
+ -
8
Ohm
Speaker
Pioneer
Amplifier
4 Ohm Bridged Mode
+
L+ R-
-
Diagram B - Improper
4
Ohm
Speaker
+ -
4
Ohm
Speaker
Pioneer
Amplifier
2 Ohm Bridged Mode
+
L+ R-
-
Published by Pioneer Corporation.
Copyright © 2005 by Pioneer Corporation.
All rights reserved.
Publication de Pioneer Corporation.
Copyright © 2005 Pioneer Corporation.
Tous droits de reproduction et de traduction
réservés.
Printed in China
Imprimé en Chine
UC <05L00000>
BRIDGEABLE FOUR-CHANNEL
POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE
PONTABLE A QUATRE VOIES
Owner’s Manual
PRS-D4000F
Mode d’emploi
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: 1-877-283-5901
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system .......................................................................................................................................... Negative type
Current consumption .................................................................................................... 27.7 A (at continuous power, 4
Ω)
Average current drawn* ...................................................................................................... 10.4 A (4
Ω for four channels)
20.2 A (4 Ω for two channels)
20.2 A (2 Ω for four channels)
Fuse ........................................................................................................................................................................ 30 A × 2
Dimensions .................................................................................................................... 304 (W) × 56 (H) × 202 (D) mm
[12 (W)
× 2-1/4 (H) × 8 (D) in]
Weight .................................................................................................... 3.0 kg (6.6 lbs.) (Leads for wiring not included)
Maximum power output ............................................................................................ 150 W
× 4 (4 Ω) / 600 W × 2 (4 Ω)
Continuous power output .......................................................... 75 W × 4 (at 14.4 V, 4 Ω, 20 Hz to 20 kHz 1.0% THD)
300 W × 2 (at 14.4 V, 4 Ω, 1 kHz 1.0% THD)
150 W × 4 (at 14.4 V, 2 Ω, 1 kHz 1.0% THD)
Load impedance ...................................................................................................................... 4
Ω (2 Ω to 8 Ω allowable)
(Bridge connection: 4
Ω to 8 Ω allowable)
Frequency response ........................................................................................................ 10 Hz to 40 kHz (+0 dB, –3 dB)
Signal-to-noise ratio .................................................................................................................... 100 dB (IHF-A network)
Distortion ........................................................................................................................................ 0.005 % (10 W, 1 kHz)
Separation .................................................................................................................................................... 70 dB (1 kHz)
Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz
Cut off slope: –12 dB/oct
High pass filter .......................................................................................................... Cut off frequency: 40 Hz to 120 Hz
Cut off slope: –12 dB/oct
Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V
Speaker: 1.6 V to 26 V
Maximum input level / impedance .................................................................................................... RCA: 6.5 V / 22 k Ω
Speaker: 26 V / 90 k Ω
Power output ........................................................................................ 75 W RMS
× 4 channels
(4 Ω and 1 % THD+N)
300 W RMS × 2 channels
(4 Ω and 1 % THD+N)
150 W RMS × 4 channels
(2
Ω and 1
% THD+N)
Signal-to-noise ratio ............................................................ 80 dBA (Reference: 1 W into 4
Ω)
Note:
• Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
• The average current drawn is nearly the maximum current drawn by this unit
when an audio signal is input. Use this value when working out total current
drawn by multiple power amplifiers.
Specifications