Photosolve 290 - Manual (Page 2)

numbers represent diopters, and the bigger the number, the closer
you can get to the object being photographed), which can be used
individually, or combined for (in this case) a total of +7. Insert the
desired lens or combination of lenses by screwing them into the
adapter. At the maximum value (+7), an object will be in focus at
between 4 and 5 inches (approximately). Check the enclosed table for
additional information. As the Viewfinder of the camera does not focus
at this distance, you’ll need to select Manual Focusing and use the LCD
to frame and focus your picture. This procedure and others assume
that you’re familiar with the basic operation of your camera, including
using the built-in screen options.
Set the Mode selector switch to CAPTURE:
• Press the
Menu button on the back of the camera.
• Press the navigational button several times until the screen displays
Advanced Focus Modes .
• Scroll down and select Manual Focus. The screen will now display
Manual Focus Setup .
• Use the navigational button to select the smallest Focus Distance
(this should be 50 cm/1.5 feet). Then press the Done button. Finally,
press the Done button once again to return you to normal CAPTURE
mode.
• Press the Display button to turn on the LCD. As this mode uses up
batteries rapidly, it is recommended that you use the Kodak AC
adapter, a separate battery pack, or keep a supply of charged NiMH
batteries on hand.
• To take pictures, simply frame the picture in the LCD, and move the
camera closer or further away to focus the object in the screen. This
may take some practice, but you’ll determine quickly what the
approximate distance should be for each of your close-up lens
combinations. We recommend that you use a tripod for this purpose,
as it will minimize camera movement and ensure the highest quality
of detail.
Using Filters with your camera
Filters can dramatically alter photographic results. Star filters,
Polarization filters, and others can be obtained through your photo
dealer. You should be aware that some filters will change the amount
of light that the camera sees, and so you will need to correct the
exposure using the EV correction capabilities of the camera. If you
notice that your pictures are coming out too light, you’ll need to
reduce the EV, and conversely, if the pictures are too dark, you’ll
need to increase the EV. The procedure to change the EV is fairly
simple (refer to your camera’s user’ guide for more information).
• Press the Scroll button on the top of the camera twice to select the
type of exposure mode you want. This causes the word AUTO to
flash in the display.
• Press the Select button multiple times and the values 0.5 EV, 1.0 EV,
1.5 EV etc. will be displayed. When your choice appears, you can
press the
Scroll button again, or wait and the camera will select this
new value.
• Take another picture and determine if the value that you have
selected is correct. Repeat the process until the picture looks good.
It’s helpful to keep notes of your process so that you can set up
quickly the next time you come across the same or similar conditions.
Important Note
Certain filters and accessories may prevent the auto-focus from
working correctly on your camera (either due to dark lighting or filter
color). If this happens (the red light will display), you should try the
Manual Focus mode, using a distance setting that is appropriate for the
scene. Alternatively, you can “trick” the camera into auto-focus, by
removing the adapter, half-pressing (and holding) the shutter, and then
reinstalling the adapter prior to pressing the shutter button all the
way. This is tricky, and is best accomplished with a tripod, but it does
work. You’ll need to check the exposure and adjust appropriately. If
you’re using a Polarization Filter with the adapter, you should turn on
the Display LCD to check the effect, before taking the picture.
Other devices
Lens Hoods such as the Ambico™ Lens hood and Cokin™ filter assembly
can be attached to your adapter, thus providing you with additional
filtering and special effects. Note that you will need to use the Manual
Focus mode, as these accessories will generally block the focusing
beam.
Care
and Feeding of your adapter
Because of the rugged design, the Xtend-a-Lens should not require any
special cleaning or care other than an occasional wipe with a clean cloth.
Please observe the following when using or storing your adapter.
• DO NOT apply solvents to the adapter
• DO NOT expose the adapter to high temperatures
• DO use the adapter for the purpose it was intended and enjoy
your new world of photography
Warranty
Xtend-a-Lens™ is warranted to be free of manufacturing defects for a
period of 90 days. If during that time, the unit becomes defective, it
should be returned to the place of purchase for replacement. The
manufacturer reserves the right to repair or replace defective units.
Units out of warranty will be repaired or replaced at a nominal fee by
the manufacturer. Contact the manufacturer to arrange return and
repair.
Thank you for your purchase of Xtend-a-Lens. We hope that it will
provide you years of satisfaction, and enjoyment. Capture the moment.
Keep on taking pictures!