Philips VR550/58 - Manual (Page 5)

Manual TV channel search
In some cases it can occur that all of the TV
channels are not found and saved during the first
installation. In this case, the missing or coded TV
channels must be searched for and stored man-
ually.
1. 1. Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2. 2. Press .The main menu will appear.
3. 3. Use or to select 'TUNER
SET UP'. Then press .
4. 4. Use or to select 'MANU-
AL TUNING'. Then press .
5. 5. Select 'PROG.' with or .
Then press .
6. 6. With or or , select
the desired programme number that you want
to use for the TV channel, e.g. 'P01'. Then
press .
7. 7. Select 'CHANNEL' with or ,
and confirm with . Then enter the
desired channel with .
If you set 'SKIP' on for a channel, this channel
will be ignored when going through the
channels with
or .
8. 8. Save the TV channel with .
9. 9. To search for other TV channels, begin again
at step 5.
10. 10. To end, press .
Using the satellite receiver
Satellite channels from a satellite receiver (con-
nected to the scart socket AV2(DECODER) ) are
received on the video recorder. Select pro-
gramme number 'AV2' with 0.0.2.
You should select the satellite channels to be
received by the satellite receiver directly on the
receiver itself.
Follow TV (Automatic TV channels
sorting)
When the automatic channel search function is
activated, the TV channels are saved in a specific
order. This may vary from the order of TV chan-
nels on the TV.
This function changes the order of TV channels
saved in the video recorder to match that of the TV.
Make sure that the video recorder and the TV
are connected by a scart cable.
1. 1. Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2. 2. Press . The main menu will appear.
3. 3. Select 'TUNER SET UP' with
and confirm with .
4. 4. Select 'FOLLOW TV' with or
and confirm with .
5. 5. 'P:01' will appear and '01' will flash in the
video recorder display.
6. 6. Select programme number '1' on the TV.
7. 7. Confirm with on the video
recorder remote control. The video recorder
compares the TV channels on the TV and the
video recorder.
If the video recorder finds the same TV chan-
nel as on the TV, then it stores it at 'P01'.
FWD 1- B
FWD 1- B
STOP C-L PLAY B-K
FWD 1- B STOP C-L
PLAY B-K
MENU
STATUS/EXIT
FWD 1 - B
P– P+
0..9
FWD 1 - B
STOP C-L PLAY B-K
FWD 1- B
0..9 STOP C-L PLAY B-K
FWD 1- B
STOP C-L PLAY B-K
FWD 1- B
STOP C-L PLAY B-K
FWD 1- B
STOP C-L PLAY B-K
MENU
EN
MANUAL TUNING
→PROG. P55
CHANNEL 055
DECODER [OFF]
SKIP [OFF]
VIDEO MODE [SECAM]
SELECT K L CHOOSE B
END=EXIT
I don’t know the channels for my TV stations
In this case, press
or in
'CHANNEL' to start the automatic channel
search. A changing channel number will appear
on the TV screen. Continue the automatic search
until you have found the desired TV channel.
STOP C-L PLAY B-K
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
END=EXIT
I cannot switch my TV to programme num-
ber '1'
If you have connected additional devices to
socket AV2 (DECODER), please disconnect
these devices. Because of other connected
devices, the TV could switch to the programme
number of the scart socket.
5
How do I change 'VIDEO MODE'?
If you want to change the video mode, select
'VIDEO MODE' with
or .
Then, press to select your desired
mode.
FWD 1- B
STOP C-L PLAY B-K
HG474ED(EN).qx3 03.12.22 9:58 PM Page 5