Philips CD SOUNDMACHINE AZ1021 - Manual (Page 4)

English Controls/Power Supply
Supplied Accessories
– AC power cord
Top/front panels (See 1)
1 VOLUME – adjusts volume level.
2 Source selector: CD,TUNER, OFF
– selects CD or radio source of sound
– power off switch
3 Display – shows the CD functions
4 2 ; – starts or pause CD playback
§ ∞
– selects the next/previous track
– searches forwards/backwards (press and
hold the button) within the current track
REPEAT – repeats a track/
CD program/entire CD.
5 PROG – programs tracks and reviews the
program
6 LIFT TO OPEN – opens/ closes the CD
door.
7 TUNING – tunes to radio stations
8 SHUFFLE – plays all tracks in random order
9 BAND – selects waveband
0 9 STOP – stops CD playback;;
– erases a CD program
Back/bottom panel ( See 2
and 3)
! Telescopic antenna - improves FM
reception.
@ AC MAINS~ - inlet for power cord.
# DBB – turns the bass enhancement on/off.
$ p – 3.5 mm stereo headphone socket
Helpful hints: The speakers will be muted
when headphones are connected to the set.
% Battery door – open to insert 6 x 1.5V
R-14 / UM-2/ C-cells
CAUTION
- Visible and invisible laser radiation.
If the cover is open, do not look at
the beam.
- High voltage! Do not open.You run
the risk of getting an electric shock.
The machine does not contain any
user-serviceable parts.
- Modification of the product could
result in hazardous radiation of
EMC or other unsafe operation.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery door and insert 6 batteries,
type R-14, UM-2 or C-cells, (preferably
alkaline) with the correct polarity as indicated
by the "+" and "–" symbols inside the com-
partment. (See 2)
2 Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set is
now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
• Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or
cause the batteries to burst:
• Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
• When inserting new batteries, do not try to mix
old batteries with the new ones.
• Remove the batteries if the set is not to be used
for a long time.
Power Supply General Operation / Tuner
Using AC power
WARNING: Always check you have com-
pletely switched off the set, before you
change or disconnect power supply.
1 Check if the power voltage, as shown on
the type plate located on the
bottom of the set,
corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 Connect the power cord to the AC
MAINS~
inlet and the wall socket.The set is
now connected and ready for use.
3 To switch the set off completely, withdraw the
power cord from the wall socket.
4 Install the unit near the AC outlet and where
the AC power plug can be easily reached.
• Disconnect the power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Helpful hints:
– To avoid unnecessary energy consumption,
always adjust the
Source selector to OFF
after using the set.
General operation
Switching on and off and selecting the
function
1 To select your sound source, adjust the
Source selector
to: CD or TUNER.
2 To switch off the set, adjust the Source
selector
to OFF position.
Adjusting volume and sound
Adjust the sound with the VOLUME and
DBB
controls.
Radio reception
1 Adjust the Source selector to TUNER.
2 Adjust BAND to select your desired
waveband, MW, or FM.
3 Turn TUNING to tune to a station.
Helpful hints:
To improve radio reception
• For FM, extend, incline and turn the telescop-
ic antenna for best reception. Reduce its
length if the signal is too strong.
• For MW, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.