Polycom VIDEOPLUS VR630/07 - Manual (Page 21)

21 EN
6. 6. The decoded data appears after confirma-
tion. You can go back to change the data.
Select the corresponding input field using
. Change the data with .
7. 7. When all information are correctly, press
. The programming information
is stored in a TIMER block.
8. 8. Insert a cassette with an intact security tab
(unprotected).
9. 9. Switch off with . The pro-
grammed recording will only function when
the video recorder is switched off with
.
If any of the TIMER blocks are in use, ' REC' will
light up on the video recorder display.
Problems and solutions for pro-
grammed recordings
Programming a recording (without
VIDEO Plus+ system)
1. 1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2. 2.Press . The main menu will appear.
3. 3.Select 'TIMER' with . Then press
.
4. 4.Select ONCE, DAILY, or WEEKLY recording
with . Then press .
If any of the TIMER blocks are in use, 'FULL' will
appear on the TV screen.
5. 5. Select TIMER block with . 0..9
B 1 L C K B
B 1
L C K B
MENU
STANDBY/ON y y
STANDBY/ON y y
STATUS/EXIT
0..9 CLEAR B 1
Switching on 'VPS/PDC' in the 'START' input
field
Select 'VPS/PDC' using
. Press '1'
to switch off 'VPS/PDC' or press '2' to switch on
'VPS/PDC'.
CLEAR B 1
Using 'Tape List'
To save a recording in 'Tape List' or to use a
'Tape List' cassette, enter the cassette number
using .
You can find more information on 'Tape List' in
the chapter 'Tape List'. If you don't want to use
Tape List, interrupt with
. STANDBY/ON y y
0..9
The video recorder will not operate
* While a programmed recording is being made,
you cannot operate your video recorder manually.
If you want to cancel the programmed recording,
press .
'TURN OFF VCR FOR TIMER RECORDING'
flashes on the TV screen
* The video recorder was switched on several min-
utes before the start of a programmed recording.
Switch off the video recorder with
.
A programmed recording (timer) will only function
if the video recorder is switched off.
STANDBY/ON y y
C / A
Cassette is ejected during recording
* The end of the tape was reached during record-
ing.
Error message: ' ' will flash in the video
recorder display
* No cassette was inserted. Insert a cassette and
switch off the video recorder using
.
Cassette was ejected as soon as the
button was pressed
* A cassette was inserted with the security tab
removed.
Undo the erase protection (chapter 'Manual
Recording', section 'Preventing accidental erasing
of cassettes') or insert a different cassette.
Error message: 'FULL'
* If this error message appears after pressing
, then all TIMER blocks are already pro-
grammed. No more recordings can be pro-
grammed. If you want to clear a programmed
recording (TIMER block), select the programme
number on TIMER LIST menu and press
. CLEAR
SV/V+
STANDBY/ON y y
STANDBY/ON y y
SELECT K L CHOOSE B
→ ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
Selecting once/daily/weekly recordings
Use
to select from the following
options:
'ONCE': Recording once
'DAILY': Repeated daily recordings from
Monday to Friday
'WEEKLY.': Repeated weekly recordings (every
week on the same day)
L C K B
Recording from a satellite channel [VR830]
If you want to record from a satellite channel,
set ‘PROG.’ SAT with ‘2’. Then, enter the satel-
lite programme number with
. 0..9
VR630/07 02.2.6 10:13 AM Page 21