Phoenix Gold RSD300.1 - Manual (Page 3)

Phoenix Gold International, Inc. • 9300 North Decatur St. Portland, OR 97203 • 503.286.9300 • www.phoenixgold.com
RSd AMPLIFIERS
MONOBLOCK OWNER’S MANUAL
BUILT-IN ELECTRONIC CROSSOVER
Monoblock: 18dB per octave electronic crossover for low-
pass and an 18dB per octave subsonic filter.
ON BOARD PROTECTION
The on-board protection circuitry monitors abnormal
conditions such as voltage spikes, short circuit and over
thermal limits. When any of these conditions exist, the
protection circuit will shut down the amplifier and light up the
protection indicator to identify the problem. Once the problem
is resolved, the amplifier will return to normal operation
automatically.
HIGH SPEED HIGH CURRENT MOSFET SWITCHING
POWER SUPPLY
High current MOSFET transistors are used in the power
supply section to minimize internal heat and maximize
reliability.
HIGH CURRENT/HIGH VOLTAGE FULLY
COMPLEMENTARY OUTPUT STAGE
Complementary output stage audio circuitry has been a
standard in high end home amplifier design. Phoenix Gold is
one of the very few car audio manufacturers to incorporate
this design approach into a mobile audio amplifier.
LINE OUTPUTS
The amplifiers full-range line outputs can be used to feed
signals to another amplifier for future expansion or for setting
up a more sophisticated system.
WIDE RANGE INPUT SENSITIVITY ADJUSTMENT
The input sensitivity level of this amplifier can be easily varied
from as low as 200 mV to as high as 8.0 volts by adjusting the
control on the Input Panel.
MULTI-FUNCTION PROTECTION INDICATOR
When the red protect indicator lights up it signifies a high
operating temperature is detected and the amplifier is
temporarily shut down to allow for a cooling period. As soon
as the temperature returns to a safe level, the amplifier will
restart and resume normal operation. This indicator also lights
up when the amplifier detects either an over-current situation,
shorted speaker outputs or a DC offset at the outputs.
Turn off the amplifier; double-check all inputs and speaker
connections to make sure there is no short or inappropriate
input. If all connections are in order, turn on the amplifier to
resume operation.
VARIABLE BASS BOOST
The bass boost will increase the output centered at 45Hz from
0 to 18dB
SPECIFICATIONS:
FEATURES:
RSd 300.1
MONOBLOCK CLASS A/B POWER AMPLIFIER
CEA-2006 Compliant Amplifier Power Standard
Frequency Response . . . . . . . . 10Hz to 300Hz
Effective Damping Factor . . . . . . 6.39 @ 4 ohms
Maximum Input . . . . . . . . . . 11.8V at clipping
Maximum Sensitivity . . . . . . . . 200mV at clipping
Ratings other than CEA-2006
Power Output . . . . . . . . . . . 360W RMS @ 2 Ohms, 100Hz and 1% THD+N
Bass Boost . . . . . . . . . . . . +18dB @ 45Hz
Low Pass Filter Frequency Response. . 30 to 300Hz Lowpass, 18dB per octave
Subsonic Filter Frequency Response . . 5 to 55Hz Highpass, 18dB per octave
Dimensions (L x W x H): . . . . . . . 12
7 /
8
” x 11 3 /
16
” x 2 3 /
8
”
RSd 600.1
MONOBLOCK CLASS D POWER AMPLIFIER
CEA-2006 Compliant Amplifier Power Standard
Power Output . . . . . . . . . . 400W RMS @ 4 ohms and 1% THD+N
Signal to Noise Ratio . . . . . . . . 82 dBA (reference: 1W output @ 4 ohms)
Frequency Response . . . . . . . . 10Hz to 300Hz
Effective Damping Factor . . . . . . 6.39 @ 4 ohms
Maximum Input . . . . . . . . . . 10V at clipping
Maximum Sensitivity . . . . . . . . 200mV at clipping
Ratings other than CEA-2006
Power Output . . . . . . . . . . . 650W RMS @ 2 ohms, 100Hz and 1% THD+N
Bass Boost . . . . . . . . . . . . +18dB @ 45Hz
Low Pass Filter Frequency Response. . 30 to 265Hz Lowpass, 18dB per octave
Subsonic Filter Frequency Response . . 5 to 55Hz Highpass, 18dB per octave
Dimensions (L x W x H): . . . . . . . 16
7 /
8
” x 11 3 /
16
” x 2 3 /
8
”
Due to continual product improvement, all specifications subject to change without notice.