Safety rules, Assembly – Poulan 452 MVB User Manual

Page 3

-- 3 --

MAINTAIN YOUR UNIT PROPERLY

Have all maintenance other than the rec-

ommended procedures described in the

Operator’s Manual performed by your

Service Dealer.

Disconnect spark plug before performing

maintenance except for carburetor adjust-

ments.

Use only recommended POULAN PRO

replacement parts; use of any other parts

may void your warranty and cause dam-

age to your unit.

Empty the fuel tank before storing the unit.

Use up fuel left in carburetor by starting the

engine and letting it run until it stops.

Do not use any accessory or attachment

other than those recommended by the

manufacturer for use with your unit.

Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from water heaters, electric

motors or switches, furnaces, etc.

Store in a dry area out of reach of children.

SPECIAL NOTICE:

For users on U.S.

Forest Land and in some states, including

California(Public Resources Codes 4442

and 4443), Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington: Certain in-

ternal combustion engines operated on for-

est, brush, and/or grass covered land in the

above areas are required to be equipped

with a spark arrestor, maintained in effective

working order, or the engine must be con-

structed, equipped, and maintained for the

prevention of fire. Check with your state or

local authorities for regulations pertaining to

these requirements. Failure to follow these

requirements is a violation of the law. This

unit is not factory equipped with a spark ar-

restor; however, a spark arrestor is available

as an optional part. If a spark arrestor is re-

quired in your area, contact your Authorized

Service Dealer for the correct kit. The spark

arrestor, blower tubes, and nozzles must be

assembled to the unit to be in full compliance

with the regulations.

SPECIAL NOTICE:

Exposure to vibra-

tions through prolonged use of gasoline

powered hand tools could cause blood ves-

sel or nerve damage in the fingers, hands,

and joints of people prone to circulation dis-

orders or abnormal swelling. Prolonged use

in cold weather has been linked to blood ves-

sel damage in otherwise healthy people. If

symptoms occur such as numbness, pain,

loss of strength, change in skin color or tex-

ture, or loss of feeling in the fingers, hands, or

joints, discontinue the use of this tool and

seek medical attention. An antivibration sys-

tem does not guarantee the avoidance of

these problems. Users who operate power

tools on a continual and regular basis must

monitor closely their physical condition and

the condition of this tool.

SAFETY RULES

ASSEMBLY

PREPARATION

WARNING:

Stop the engine and be

sure the impeller blades have stopped turn-

ing before opening the vacuum inlet door or

attempting to insert or remove the vacuum

tubes. The rotating blades can cause seri-

ous injury.

WARNING:

If you receive your unit

assembled, check each step to insure your

unit is properly assembled. Follow all safety

information in the manual and on the unit.

BLOWER TUBE ASSEMBLY

Assemble the blower tube and nozzle to

the unit (turn clockwise to tighten).

Blower

Tube

Nozzle

Blower

Outlet

SHOULDER STRAP ASSEMBLY

(for blower use only)

Pass the shoulder strap over your head

and onto your left shoulder.

Snap the hook onto the retainer on the top

handle.

Retainer

VACUUM BAG ASSEMBLY

Open the zipper on the vacuum bag and in-

sert the elbow tube.

Push the end of the elbow tube with the

grooves through the small bag tube open-

ing. Make sure the bag tube opening is

flush against large raised rib on the tube.

Close the zipper on the bag. Make sure the

zipper is closed completely and the zipper

seam is tucked toward inside of the bag.

Bag Tube

Opening

Raised Rib

Zipper

Opening

This manual is related to the following products:

530087725