Philips TS2744C - Manual (Page 5)

ON VOL. BAR
EXIT
SETUP
BRIGHTNESS
PICTURE
COLOR
OFF
VOLUME
STATUS/EXIT
CH
CH
POWER
VOL
VOL
MENU
A/CH
MUTE
CC
SLEEP
1
2
3 4
5
6 7
8
9
0
1
2
3
VOL. LIMIT
STATUS/EXIT
CH
CH
POWER
VOL
VOL
MENU
A/CH
MUTE
CC
SLEEP
1
2
3 4
5
6 7
8
9
0
1
2
3
1
O
N
-S
CREEN
MENU C
ONTROLS
(
CONTINUED
)
U se the Volume Bar con-
trol to see the TV’s vol-
ume level settings on the TV
screen. Once set the Volume
Bar will be seen each time
the VOLUME buttons (on the
TV or remote) are pressed.
V OLUME B AR
Press the MENU (M)
button on the remote, then
press the CH (+) or (–) (or
press the MENU ▲ or ▼ but-
tons on the TV) to select the
word VOL. BAR with the
TV’s on-screen Arrow.
Press the VOL (+) or (-)
buttons to turn the VOL BAR
control ON or OFF. Try it out.
Press the VOL (+)
or (–) buttons. The
VOLUME BAR
should appear at the
bottom of the
screen.
NOTE: The TV's
volume level can
also be lowered
when the set is
turned OFF.
S MART
H ELP Press STATUS button to
clear the screen.
V OLUME BEGIN
Y ou can limit the maximum
volume level of the TV
set. Once the Volume Limiter
control is set the TV sound
cannot be played louder than
the maximum preset level.
L IMITING THE V OLUME
Press numbers 0, 7, 2,
0, 9, 1; then press MENU (M)
button on the remote or TV.
The VOL. LIMIT bar will
show on the screen.
Press the VOLUME (+)
or (–) button until the VOL.
LIMIT bar is at the level you
want to be the highest possible
volume.
Remember,
the Volume Limit
Bar will appear to
return to the low end
of the register (when
the STATUS button
is pressed to set the
desired maximum
volume level - step #
3). This is normal for
setting the Volume
Limiter. Your new
maximum volume
level has been kept
in memory.
S MART
H ELP Press the STATUS but-
ton to set the maximum vol-
ume level. The screen will
clear and the TV will return to
normal channel viewing.
BEGIN
12
ON STEREO
CABLE
CHANNEL
SLEEP
CAPTION
VOL. BAR
STEREO
OFF
STATUS/EXIT
CH
CH
POWER
VOL
VOL
MENU
A/CH
MUTE
CC
SLEEP
1
2
3 4
5
6 7
8
9
0
1
3
2
Y our TV can receive
broadcast stereo TV pro-
grams. The TV has both an
amplifier and twin speakers
through which the stereo
sound can be heard.
S TEREO TV S OUND
Press the MENU (M)
button on the remote, then the
CHANNEL ▲ or ▼ buttons (or
the MENU ▲ or ▼ buttons on
the TV) to select the word
STEREO with the TV’s on-
screen Arrow.
Press the VOLUME (+)
or (–) buttons to turn the
STEREO mode ON or off. Remember,
if the TV is
set to STEREO but
the current channel
is not broadcasted
in stereo, the sound
at the TV will
remain monaural.
S MART
H ELP Press the STATUS but-
ton on the remote control to
clear the screen.
S
TEREO BEGIN
NOTE: The TV’s on-screen “STEREO”
indicator appears whenever the TV detects an
incoming stereo signal. Be sure the TV’s
STEREO control is also turned “ON” in order
for the stereo sound to be heard through the
TV’s twin speaker system.
NOTE: Not all features (and
drawings) discussed in this
manual will necessarily
match those found with
your television set. This is
normal and does not require
you contacting your dealer
or requesting service.
5 - IB7759 E001